参数资料
| 型号： | CAT9534YI-GT2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16TSSOP |
| 标准包装： | 1 |
| 接口： | I²C，SM 总线 |
| 输入/输出数： | 8 |
| 中断输出： | 是 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 标准包装 |
| 包括： | POR |
| 产品目录页面： | 806 (CN2011-ZH PDF) |
| 其它名称： | CAT9534YI-GT2DKR |
CAT9534
http://onsemi.com
5
SCL
SDA IN
SDA OUT
Figure 2. I2C Serial Interface Timing
tSU:STA
tAA
tF
tHD:STA
tHD:DAT
tLOW
tDH
tR
tSU:DAT
tLOW
tHIGH
tSU:STO
tBUF
Pin Description
SCL: Serial Clock
The serial clock input clocks all data transferred into or out
of the device. The SCL line requires a pullup resistor if it
is driven by an open drain output.
SDA: Serial Data/Address
The bidirectional serial data/address pin is used to transfer
all data into and out of the device. The SDA pin is an open
drain output and can be wireORed with other open drain or
open collector outputs. A pullup resistor must be connected
from SDA line to VCC. The value of the pullup resistor, RP,
can be calculated based on minimum and maximum values
A0, A1, A2: Device Address Inputs
These inputs are used for extended addressing capability.
The A0, A1, A2 pins should be hardwired to VCC or VSS.
When hardwired, up to eight CAT9534s may be addressed
on a single bus system. The levels on these inputs are
compared with corresponding bits, A2, A1, A0, from the
slave address byte.
I/O0 to I/O7: Input / Output Ports
Any of these pins may be configured as input or output.
The simplified schematic of I/O0 to I/O7 is shown in
Figure 5. When an I/O is configured as an input, the Q1 and
Q2 output transistors are off creating a high impedance
input. If the I/O pin is configured as an output, the pushpull
output stage is enabled. Care should be taken if an external
voltage is applied to an I/O pin configured as an output due
to the low impedance paths that exist between the pin and
either VCC or VSS.
Figure 3. Minimum RP Value vs.
Supply Voltage
Figure 4. Maximum RP Value vs.
Bus Capacitance
VCC (V)
CBUS (pF)
4.8
4.4
4.0
3.6
3.2
2.8
2.4
2.0
0
0.5
1.0
1.5
2.0
2.5
400
350
300
200
150
100
50
0
1
2
3
4
6
7
8
R
Pmin
(K
W
)
R
Pmax
(K
W
)
5.2
5.6
IOL = 3 mA @ VOLmax
250
5
Fast Mode I2C Bus /
tr max 300 ns
NOTE: According to the Fast Mode I2C bus specification, for bus capacitance up to 200 pF, the pull up device can be a resistor. For bus
loads between 200 pF and 400 pF, the pullup device can be a current source (Imax = 3 mA) or a switched resistor circuit.
相关PDF资料 |
PDF描述 |
|---|---|
| CAT9534WI-GT2 | IC I/O EXPANDER I2C 8B 16SOIC |
| ATMEGA8535L-8MUR | MCU AVR 8K FLASH 8MHZ 44QFN |
| PCA9535EDTR2G | 16-BIT I/O EXPANDER 24TSSOP |
| PCA9535ECMTTXG | 16-BIT I/O EXPANDER |
| ATMEGA88P-20MUR | MCU AVR 8KB FLASH 20MHZ 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT9552HV6GI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
| CAT9552HV6I-GT2 | 功能描述:LED照明驱动器 16Ch I2C-Bus LED Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT9552HV6I-TG2 | 功能描述:IC LED DRIVER LINEAR 24-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT |
| CAT9552WI-T1 | 功能描述:LED照明驱动器 16Ch I2C-Bus LED Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT9552YI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。