参数资料
| 型号： | CBC-EVAL-11 |
| 厂商： | Cymbet Corporation |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | INDUCTIVE CHARGING EVAL KIT |
| 产品培训模块： | Energy Processing and Solid State Batteries for Energy Harvesting |
| 标准包装： | 1 |
| 系列： | EnerChip™ CC |
| 主要目的： | 电源管理，电池充电器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | CBC3150 |
| 主要属性： | RF 感应充电系统 |
| 次要属性： | USB 供电 13.56 MHz 发射器 |
| 已供物品： | 2 板，线缆 |
| 相关产品： | 859-1008-6-ND - IC BATT SOLID ST ENERCHIP 20DFN 859-1008-1-ND - IC BATT SOLID ST ENERCHIP 20DFN CBC3150-D9C-TR5-ND - IC BATT SOLID ST ENERCHIP 20DFN 859-1008-2-ND - IC BATT SOLID ST ENERCHIP 20DFN 859-1007-5-ND - IC BATT SOLID ST ENERCHIP 20DFN |
| 其它名称： | 859-1003 |
EnerChip CC CBC3150
EnerChip CC CBC3150 PCB Layout Guidelines - Important Notice!
There are several PCB layout considerations that must be taken into account when using the CBC3150:
1. All capacitors should be placed as close as possible to the EnerChip CC. The flying capacitor connections
must be as short as possible and routed on the same layer the EnerChip CC is placed.
2. Power connections should be routed on the layer the EnerChip CC is placed.
3. A ground (GND) plane in the PCB should be used for optimal performance of the EnerChip CC.
4. Very low parasitic leakage currents from the V BAT pin to power, signal, and ground connections, can result
in unexpected drain of charge from the integrated power source. Maintain sufficient spacing of traces and
vias from the V BAT pin and any traces connected to the V BAT pin in order to eliminate parasitic leakage
currents that can arise from solder flux or contaminants on the PCB.
5. Pin 1 V BAT and Pin 4 V CHG must be tied together for proper operation.
6. There should be no traces, vias or connections under the CBC3150 exposed die pad.
7. When placing a silk screen on the PCB around the perimeter of the package, place the silk screen outside
of the package and all metal pads. Failure to observe this precaution can result in package cracking during
solder reflow due to the silk screen material interfering with the solder solidification process during cooling.
8. See Figure 12 for location and dimensions of metal pad placement on the PCB.
Important Note: Designers using EnerChips in their products should also download the EnerChip User Manual
Application Note AN-1026 found here: http://www.cymbet.com/products/datasheets-downloads.php.
Figure 12: Recommended PCB Layout for the CBC3150-D9C Package (Dimensions in mm)
Cymbet Logo
Lot Number
Part Number
Date Code
CBC3150
Labeling
Information
Placement
DS-72-03 Rev F
?2009-2013 Cymbet Corporation ? Tel: +1-763-633-1780 ? www.cymbet.com
Page 14 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| CBJ157 | TRS JACK STR PCB SLD POT 3-LUG |
| CBJ70 | TRB JACK STR PCB 3-LUG |
| CBJR12 | MINI-WECO PATCH JACK 75OHM R/A |
| CBJR157 | TTM JACK R/A CIR BOARD MNT 3-LUG |
| CBJR20A | BNC JACK 50 OHM R/A PCB TALL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CBC-EVAL-11 - DSC | 功能描述:CBC3150 EnerChip? CC Series Power Management, Wireless Power Supply Evaluation Board 制造商:cymbet corporation 系列:EnerChip?? CC 零件状态:有效 主要用途:电源管理，无线电源 嵌入式:否 使用的 IC/零件:CBC3150 主要属性:RF 感应充电系统 辅助属性:USB 供电 13.56 MHz 发射器 所含物品:2 板，线缆 标准包装:1 |
| CBC-EVAL-11_12 | 制造商:CYMBET 制造商全称:CYMBET 功能描述:EnerChip CC Inductive Charging Evaluation Kit |
| CBC-EVAL-12 | 制造商:CYMBET 制造商全称:CYMBET 功能描述:SPI Real-Time Clock/Calendar with Integrated Backup Power |
| CBC-EVAL-12-34123 | 功能描述:CBC34123 EnerChip? Series Power Management/Timing, Battery, Real Time Clock (RTC) Evaluation Board 制造商:cymbet corporation 系列:EnerChip?? 零件状态:有效 主要用途:电源管理/定时，电池，实时时钟（RTC） 嵌入式:- 使用的 IC/零件:CBC34123 主要属性:薄膜充电式固态电池 辅助属性:USB，SPI 接口 所含物品:2 个板 标准包装:1 |
| CBC-EVAL-12-34803 | 功能描述:CBC34803 EnerChip? Series Power Management/Timing, Battery, Real Time Clock (RTC) Evaluation Board 制造商:cymbet corporation 系列:EnerChip?? 零件状态:有效 主要用途:电源管理/定时，电池，实时时钟（RTC） 嵌入式:- 使用的 IC/零件:CBC34803 主要属性:薄膜充电式固态电池 辅助属性:USB，I2C接口 所含物品:2 个板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。