- 您现在的位置：买卖IC网 > PDF目录16761 > CBC3105-R4C (Cymbet Corporation)IC POWER MANAGEMENT PDF资料下载
参数资料
| 型号： | CBC3105-R4C |
| 厂商： | Cymbet Corporation |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC POWER MANAGEMENT |
| 标准包装： | 92 |
| 系列： | EnerChip™ |
| 其它名称： | 859-1022 |
Preliminary
EnerChip CC CBC3105
EnerChip CC Detailed Description
The EnerChip CC uses a charge pump to generate the supply voltage for charging the integrated energy storage
device. An internal FET switch with low RDS ON is used to route V DD to V OUT during normal operation when main
power is above the switchover threshold voltage. When V DD is below the switchover threshold voltage, the
FET switch is shut off and V OUT is supplied by the EnerChip. An interrupt signal is asserted low prior to the
switchover.
Operating Modes
The EnerChip CC can be operated from various power supplies such as a primary source or a non-rechargeable
battery. With the ENABLE pin asserted high, the charge pump is active and charges the integrated EnerChip.
The EnerChip CC will be 80% charged within 10 minutes. Due to the rapid recharge it is recommended that,
once the EnerChip CC is fully charged, the user de-assert the ENABLE pin (i.e., force low) to reduce power
consumption. A signal generated from the MCU could be used to enable and disable the EnerChip CC.
When controlling the ENABLE pin by way of an external controller - as opposed to fixing the ENABLE line to VDD
- ensure that the ENABLE pin is forced low by the controller anytime the RESET line is low, which occurs when
the switchover threshold voltage is reached and the device is placed in backup mode. Although the internal
charge pump is designed to operate below the threshold switchover level when the ENABLE line is active, it
is recommended that the ENABLE pin be forced low whenever RESET is low to ensure no parasitic loads are
placed on the EnerChip while in this mode. If ENABLE is high or floating while VDD is in an indeterminate
state, bias currents within the EnerChip CC could flow, placing a parasitic load on the EnerChip that could
dramatically reduce the effective backup operating time.
The EnerChip CC supports 2 operational modes as shown in Figures 6 and 7.
Mode 1 Operation
For use in 3.3 volt systems. The V MODE pin should be tied directly to GND, as shown in Figure 6. This will set the
switchover threshold at approximately 3.0 volts.
Figure 6: CBC3105 Typical Circuit for Mode 1 Operation
DS-72-21 Rev E
?2012 Cymbet Corporation ? Tel: +1-763-633-1780 ? www.cymbet.com
Page 9 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| 100RX3022M8X11.5 | CAP ALUM 22UF 100V 20% RADIAL |
| ECM22DCBS-S189 | CONN EDGECARD 44POS R/A .156 SLD |
| 0982660312 | CBL 28POS 0.5MM JMPR TYPE D 10" |
| H3BBH-3406G | IDC CABLE - HSR34H/AE34G/HSR34H |
| 342A058-4/42-0 | BOOT MOLDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CBC3105-R4C-TR1 | 功能描述:电子电池 5uAhr EnerChip CC 4x5 DFN-20-70C 1K RoHS:否 制造商:Cymbet 电池大小:9 mm x 9 mm 输出电压:3.3 V 容量:50 uAh 化学性质: 端接类型:SMD/SMT 可再充电/不可再充电:Rechargeable |
| CBC3105-R4C-TR5 | 功能描述:电子电池 5uAhr EnerChip CC 4x5 DFN-20-70C 5K RoHS:否 制造商:Cymbet 电池大小:9 mm x 9 mm 输出电压:3.3 V 容量:50 uAh 化学性质: 端接类型:SMD/SMT 可再充电/不可再充电:Rechargeable |
| CBC3105-R4C-WP | 制造商:CYMBET 制造商全称:CYMBET 功能描述:EnerChip CC with Integrated Power Management |
| CBC3112 | 制造商:CYMBET 制造商全称:CYMBET 功能描述:Epson RX-8564 RTC Power Backup with EnerChip Battery |
| CBC3112-D7C | 功能描述:电子电池 12uAhr EnerChip and CBC910 7x7MLF C Temp RoHS:否 制造商:Cymbet 电池大小:9 mm x 9 mm 输出电压:3.3 V 容量:50 uAh 化学性质: 端接类型:SMD/SMT 可再充电/不可再充电:Rechargeable |
发布紧急采购，3分钟左右您将得到回复。