- 您现在的位置：买卖IC网 > PDF目录385229 > CBF1602-10RFI (TT Electronics / Welwyn) Tubular Vitreous Enamelled Wirewound Resistors PDF资料下载
参数资料
| 型号： | CBF1602-10RFI |
| 厂商： | TT Electronics / Welwyn |
| 英文描述： | Tubular Vitreous Enamelled Wirewound Resistors |
| 中文描述： | 管状玻璃搪瓷绕线电阻 |
| 文件页数： | 5/7页 |
| 文件大小： | 338K |
| 代理商： | CBF1602-10RFI |
Tubular Vitreous Enamelled
Wirewound Resistors
1600/1900 Series
Welwyn Components Limited
Bedlington, Northumberland NE22 7AA, UK
Telephone: +44 (0) 1670 822181 · Facsimile: +44 (0) 1670 829465 · Email: info@welwyn-tt.com · Website: www.welwyn-tt.com
123
Issue E · 10.05
Welwyn Components
Maximum*
total
dissipation
in 20°C
ambient
(watts) with
single tap
Maximum*
resistance
with single
tap
(ohms)
Maximum*
number
of taps
Type
1905
14.5
9k
1
1600
15.0
12k
1
1602
15.5
9k
1
1906
19.0
13k
1
1603
22
18k
1
1604
31
29k
2
1605
41
34k
2
1908
47
38k
2
1607
66
53k
2
1606
80
78k
4
1608
101
93k
4
1609
145
140k
4
Tapped Resistors
See Figure 10
Fixed resistors can be supplied with taps to special order.
Because of the reduced winding length, the total resistance of
a tapped resistor will be less than can be offered on a fixed
resistor of the same size. The reduction is proportional to the
number of taps and Table 5 is intended as a guide.
The minimum resistance per section on all sizes is 1
and the
standard selection tolerance for any section is ±10%
Ordering Procedure
Enquiries for tapped resistors must state the following details:
Resistance per section
Maximum dissipation per section
Maximum operating ambient temperature
Maximum permissible dimensions if important
Type of terminations required. (See ‘Terminations’, page 3)
Resistor style or proposed method of mounting.
Table 5
*Maximum total dissipation assumes that this will be
evenly spread over the total element length.
Low Inductance Resistors
Ayrton-Perry wound elements are supplied for low inductance
applications. This winding style has a maximum permissible
hot spot temperature of 300°C. The maximum dissipation is
defined in Table 1 under the heading Operating hot spot
temperature of 300°C, and resistance ranges are defined in
the three right-hand columns of this table.
Application Notes
When cold, vitreous enamel has excellent insulation resistance.
In common with all insulants the specific resistance of the
enamel decreases with increased temperature; therefore, if
operated at any temperature approaching the maximum, the
resistor cannot be classed as an insulated type and should not
be used in contact with any conducting materials.
The recommended dissipations for each of the resistor hot
spot temperatures applies to resistors mounted horizontally. If
the bore is completely blocked a 15% derating is
recommended. However, wherever possible, resistors should
be mounted vertically with unobstructed bore.
This makes best use of the chimney effect of the heated tube
and will encourage a cooling stream of air through the bore.
Allowances must be made, when tubular resistors are mounted
in banks, for the effects produced by radiation between tubes.
Appreciable reduction of hot spot temperature can be
achieved by arranging that resistors are subjected to some
measure of forced draught. In general, it is most efficient to
extract air from the resistor enclosure and arrange that an air
inlet is adjacent to the bottom of the tubes.
If soft soldered connections are used the resistors should be derated
where applicable to limit the hot spot temperature to 300°C.
相关PDF资料 |
PDF描述 |
|---|---|
| CBF1602-10RGI | Tubular Vitreous Enamelled Wirewound Resistors |
| CBF1602-10RJI | Tubular Vitreous Enamelled Wirewound Resistors |
| CBF1602-10RKI | Tubular Vitreous Enamelled Wirewound Resistors |
| CBF1603-10RFI | Tubular Vitreous Enamelled Wirewound Resistors |
| CBF1603-10RGI | Tubular Vitreous Enamelled Wirewound Resistors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CBF1602-10RGI | 制造商:WELWYN 制造商全称:Welwyn Components Limited 功能描述:Tubular Vitreous Enamelled Wirewound Resistors |
| CBF1602-10RJI | 制造商:WELWYN 制造商全称:Welwyn Components Limited 功能描述:Tubular Vitreous Enamelled Wirewound Resistors |
| CBF1602-10RKI | 制造商:WELWYN 制造商全称:Welwyn Components Limited 功能描述:Tubular Vitreous Enamelled Wirewound Resistors |
| CBF1603-10RFI | 制造商:WELWYN 制造商全称:Welwyn Components Limited 功能描述:Tubular Vitreous Enamelled Wirewound Resistors |
| CBF1603-10RGI | 制造商:WELWYN 制造商全称:Welwyn Components Limited 功能描述:Tubular Vitreous Enamelled Wirewound Resistors |
发布紧急采购，3分钟左右您将得到回复。