- 您现在的位置：买卖IC网 > PDF目录10901 > CC-2401K2A-CS5 (Copeland Communications Inc)MODEM 2400BAUD SECURE 5V PDF资料下载
参数资料
| 型号： | CC-2401K2A-CS5 |
| 厂商： | Copeland Communications Inc |
| 文件页数： | 2/66页 |
| 文件大小： | 0K |
| 描述： | MODEM 2400BAUD SECURE 5V |
| 标准包装： | 30 |
| 数据格式： | V.21，V.22，V.23，Bell 103 |
| 波特率： | 2.4k |
| 电源电压： | 4.2 V ~ 7 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 模块 |
| 包装： | 散装 |
| 配用： | 539-1002-ND - KIT EVALUATION WORLD MODEM II |
| 其它名称： | 539-1009 CC-2401K2A-CS5-ND |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
Data Sheet
CC-2401K2
Page 10 of 66
2007, Copeland Communications, Inc.
CC-2401K2 Datasheet Rev 1.5
Command / Data Mode
On Reset, the CC-2401 is in command mode.
In this mode, the modem accepts AT commands.
Type
“ATDT#” (tone dial) to initiate a call once the modem has been initialized. Use ATDP for pulse lines. Every
command must be followed by a carriage return. Once a connection is established, the modem responds with
“c, “d”, or “v” and enter data mode. Once in this mode, the modem will not respond to AT style commands.
There are three ways to return to command mode:
-
Use the ESC pin.
To enable the ESC pin feature, set SE2[5:4) = 11. A positive edge on this pin will
return the modem to command mode. To reenter data mode, type “ATO”.
-
Use 9-bit data mode. If 9-bit data format with escape is configured a 1 detected on bit 9 returns the
modem to command mode. To enable this feature, set SE0[3] (ND) = 1 and S15[0] (NBE) = 1. Again,
use “ATO” to return to data mode.
-
Use “+++”. The escape sequence is a sequence of three escape characters that are set in S-register S0F
(“+” character is the default escape). If this sequence is seen and the modem detects no activity on the
line before or after, the modem will return to command mode.
No matter the escape method, when carrier is lost, the modem will return to command mode and reports “N”.
Flow Control
Flow control is only needed if the DTE and DCE rate are not the same. If the DTE rate is set higher than the
line (DCE), flow control is required to prevent data loss to the transmitter.
To control data flow, the CTS pin is used. When CTS is asserted, the CC-2401 is ready to accept a character.
While CTS is negated, no data should be sent to the modem on TXD. To simplify flow control, the CC-2401
has an integrated ten character transmit FIFO and allows for two different CTS reporting methods. By default,
the CTS pin is negated as soon as a start bit is detected on the TXD pin and remains negated until the modem
is ready to accept another character. Setting SFC7[7]=1 (CTSM), CTS is negated when the FIFO is 70% full
and is reasserted when the FIFO is 30% full.
Power Save Modes
The CC-2401 has three low power modes:
-
DSP Power down. The DSP processor can be powered down by setting SEB[3](PDDE) = 1. In this
mode, the serial interface still functions and the modem detects ringing and intrusion. No modem modes
or tone detection features function.
-
Wake on Ring.
Issuing ATz command causes the modem into a low power mode where both the
controller and DSP are powered down. Only an incoming ring, a low TXD signal, or a total reset will
power up the modem again. Return from wake-on-ring triggers the INT pin if S09[6] (WOR) = 1.
-
Total Power down. SF1[5] = 1 and SF1[6] = 1 places the modem into total powerdown mode. All logic,
including the crystal, is powered down.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16C54T-LP/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54T-LPI/SS | IC MCU OTP 512X12 20SSOP |
| VE-261-IX-F2 | CONVERTER MOD DC/DC 12V 75W |
| PIC16C54T-LPI/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54T-LPE/SS | IC MCU OTP 512X12 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CC24020N | 制造商:POWEREX 制造商全称:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 20 Amperes/300-600 Volts |
| CC2403020N | 制造商:POWEREX 制造商全称:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 20 Amperes/300-600 Volts |
| CC2403500N | 制造商:POWEREX 制造商全称:Powerex Power Semiconductors 功能描述:Super Fast Recovery Dual Diode Modules 50 Amperes/300-600 Volts |
| CC-2404K2A-CS | 功能描述:MODEM 2400BAUD SERIAL 3.3V RoHS:否 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:- 标准包装:25 系列:- 数据格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| CC-2404K2A-CS5 | 功能描述:MODEM 2400BAUD SERIAL 5V RoHS:否 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:- 标准包装:25 系列:- 数据格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
发布紧急采购，3分钟左右您将得到回复。