- 您现在的位置：买卖IC网 > PDF目录10901 > CC-93K2N-CS5 (Copeland Communications Inc)MODEM 56KBAUD SERIAL V.92 5V PDF资料下载
参数资料
| 型号： | CC-93K2N-CS5 |
| 厂商： | Copeland Communications Inc |
| 文件页数： | 17/64页 |
| 文件大小： | 0K |
| 描述： | MODEM 56KBAUD SERIAL V.92 5V |
| 标准包装： | 30 |
| 数据格式： | V.22，V23，V.32，V.34，V.90，V.92，Bell 103，Bell 212A |
| 波特率： | 56k |
| 电源电压： | 4.2 V ~ 7 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 模块 |
| 包装： | 散装 |
| 其它名称： | 539-1013 CC-92K2N-CS5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
Data Sheet
World Modem NET
Page 24 of 64
2005 Copeland Communications, Inc.
World Modem NET Datasheet Rev 1.0
Extended AT& Command Set (Command Defaults in Bold) (Continued)
Command
Action
&H7
ITU-T V.22 only (1200 bps)
&H8
Bell 212 only (1200 bps)
&H9
Bell 103 only (300 bps)
&H10
ITU-T V.21 only (300 bps)
&H11
V.23 (1200/75 bps)
&Pn
Japan pulse dialing
&P0
Configure modem for 10 pulse-per-second pulse dialing (Japan)
&P1
Configure modem for 20 pulse-per-second pulse dialing (Japan)
&Tn
Test mode
&T0
Cancel test mode (Escape to command mode to issue AT&T0). This command will also report the
number of bit errors encountered on the previous &T4 test.
&T2
Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the
DSP (CC-14.4K2/CC-33K2/CC-56K2 only). The modem echoes data from TX pin back to RX pin.
&T3
Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the
DSP, DAA interface section, DAA interface and analog hybrid circuit. The modem echoes data
from TX pin back to RX pin.
Initiate transmit as originating modem with automatic data generation. Modulation, data rate and
symbol rate are set by &H, &G and S41. Data pattern is set by the S40 register. Continues until
the ATH command is sent after an escape into command mode.
&T4
Data is also demodulated as in ANALOOP, and any bit errors are counted to be displayed after the
test using &T0.
Initiate transmit as answering modem with automatic data generation. Modulation, data rate, and
symbol rate are set by &H, &G and S41. Data pattern is set by the S40 register. Continues until
ATH command is sent after escape into command mode.
&T5
Data is also demodulated as in ANALOOP, and any bit errors are counted to be displayed after the
test using &T0.
&T6
Compute checksum for firmware-upgradeable section of program memory. If no firmware upgrade
is installed, &T6 returns 0x0408.
&Xn
Automatic determination of telephone line type.
&X0
Abort &x1 or &x2 command
相关PDF资料 |
PDF描述 |
|---|---|
| CC-56K2N-CS5 | MODEM 56KBAUD SERIAL 5V |
| CC-2404K2N-CS5 | MODEM 2400BAUD SERIAL 5V |
| SI3015-BS | IC ISOMODEM LINE-SIDE DAA 16SOIC |
| PIC16C54T-XTE/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54T-RC/SS | IC MCU OTP 512X12 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CC94.0 | 制造商:Schneider Electric 功能描述:THERMAL UNIT |
| CC9418P | 制造商:Honeywell Sensing and Control 功能描述: |
| CC9418S | 制造商:Honeywell Sensing and Control 功能描述: |
| CC-9604C | 制造商:Ameba Technology Inc 功能描述:Board and Mini Case Cameras Sony 1-3 Super Had CCD Sensor an |
| CC-9801166-1250' | 制造商:DigitHead Inc 功能描述:1250'CUSTOM ALPHA CABLE#6032C, PER DRAWING 9801166B |
发布紧急采购，3分钟左右您将得到回复。