- 您现在的位置：买卖IC网 > PDF目录375653 > CDACV10M7GA001-R0 (MURATA MANUFACTURING CO LTD) Ceramic Filters (CERAFIL) for FM Receivers PDF资料下载
参数资料
| 型号： | CDACV10M7GA001-R0 |
| 厂商： | MURATA MANUFACTURING CO LTD |
| 英文描述： | Ceramic Filters (CERAFIL) for FM Receivers |
| 中文描述： | 10.7 MHz, BAND PASS FILTER |
| 文件页数： | 7/57页 |
| 文件大小： | 854K |
| 代理商： | CDACV10M7GA001-R0 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
6
Notice (Soldering and Mounting)
1. Standard Reflow Soldering Condition
(1) Reflow
The component cannot be withstand washing.
2. Wash
Lead terminal is directly contacted with the tip of
soldering iron of 280
±
5C for 3.0
±
0.5 seconds.
(2) Soldering Iron
60
30
Time(sec.)
5sec.
150
230
240
T
°
C
Gradual Cooling
I
Notice (Handling)
1. The component will be damaged when an excessive
stress is applied.
2. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
3. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
4. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause
destruction resistance characteristics to lower. To
prevent this, be extremely careful in determining shape
and dimension before designing the circuit board
diagram.
5. When the positioning claws and pick up nozzle are worn,
the load is applied to the chip while positioning is
concentrated to one positioning accuracy, etc. Careful
checking and maintenance are necessary to prevent
unexpected trouble.
6. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component. Depending on the soldering conditions, the
effective area of terminations may be reduced. the use of
solder containing Ag should be done to prevent the
electrode erosion.
7. Do not clean or wash the component as it is not
hermetically sealed.
8. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated well.
9. Do not use strong acidity flux, more than 0.2wt% chlorine
content, in re-flow soldering.
10. Accurate test circuit values are required to measure
electrical characteristics.It may be a cause of mis-
correlation if there is any deviation, especially stray
capacitance, from the test circuit in the specification.
[Component direction]
[Component layout close to board]
Put the
component
lateral to the
direction in
which stress
acts.
Susceptibility to
stress is in the order
of : A>C>B
B
A
C
Slit
Perforation
相关PDF资料 |
PDF描述 |
|---|---|
| CDACV10M7GA016-R0 | Ceramic Filters (CERAFIL) for FM Receivers |
| CDACV10M7GA046-R0 | Ceramic Filters (CERAFIL) for FM Receivers |
| CDACV10M7GA069-R0 | Ceramic Filters (CERAFIL) for FM Receivers |
| CDR01BP109BBWP | CERAMIC CHIP/MIL-PRF-55681 |
| CDR01BP109ADWR | CERAMIC CHIP/MIL-PRF-55681 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDACV10M7GA016-R0 | 功能描述:信号调节 10.7MHZ CERAMIC DISC RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| CDACV10M7GA018-R0 | 功能描述:信号调节 10.7MHz +/-30% Discriminator (FM) RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| CDACV10M7GA046-R0 | 功能描述:信号调节 10.7MHZ CERAMIC DISC RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| CDACV10M7GA051-R0 | 制造商:Murata Manufacturing Co Ltd 功能描述: |
| CDACV10M7GA069-R0 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:Ceramic Filters (CERAFIL) for FM Receivers |
发布紧急采购，3分钟左右您将得到回复。