- 您现在的位置：买卖IC网 > PDF目录375653 > CDACV10M7GA069-R0 (MURATA MANUFACTURING CO LTD) Ceramic Filters (CERAFIL) for FM Receivers PDF资料下载
参数资料
| 型号： | CDACV10M7GA069-R0 |
| 厂商： | MURATA MANUFACTURING CO LTD |
| 英文描述： | Ceramic Filters (CERAFIL) for FM Receivers |
| 中文描述： | 10.7 MHz, BAND PASS FILTER |
| 文件页数： | 11/57页 |
| 文件大小： | 854K |
| 代理商： | CDACV10M7GA069-R0 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
10
2
Notice (Soldering and Mounting)
1. Standard Reflow Soldering Condition
(1) Reflow
The component cannot be withstand washing.
2. Wash
Filter shall be soldered at 280
±
5C for 3.0
±
0.5 seconds.
The soldering iron shall not touch the filter white soldering.
(2) Soldering Iron
T
100
200
240
30 sec.
min.
30 sec.
max.
Peak
(240C max.)
Pre-heating
(120-170C)
Heating
(200C)
Gradual
Cooling
120 sec.
min.
60-120 sec.
I
Notice (Handling)
1. The component will be damaged when an excessive
stress is applied.
2. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
3. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
4. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause destruction
resistance characteristics to lower. To prevent this, be
extremly careful in determining shape and dimension
before designing the circuit board diagram.
5. When the positioning claws and pick up nozzle are worn,
the load is applied to the chip while positioning is
concentrated to one positioning accuracy, etc. Careful
checking and maintenance are necessary to prevent
unexpected trouble.
6. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component. Depending on the soldering conditions, the
effective area of terminations may be reduced. The use
of solder containing Ag should be done to prevent the
electrode erosion.
7. Do not clean or wash the component as it is not
hermetically sealed.
8. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated well.
9. Do not use strong acidity flux, more than 0.2wt% chlorine
content, in re-flow soldering.
10. Accurate test circuit values are required to measure
electrical characteristics.
It may be a cause of mis-correlation if there is any
deviation, especially stray capacitance, from the test
circuit in the specification.
[Component layout close to board]
Susceptibility to
stress is in the order
of : A>C>B
B
A
C
Slit
Perforation
相关PDF资料 |
PDF描述 |
|---|---|
| CDR01BP109BBWP | CERAMIC CHIP/MIL-PRF-55681 |
| CDR01BP109ADWR | CERAMIC CHIP/MIL-PRF-55681 |
| CDR01BP109BBSM | CERAMIC CHIP/MIL-PRF-55681 |
| CDR01BP109BBSP | CERAMIC CHIP/MIL-PRF-55681 |
| CDR01BP109BBSR | CERAMIC CHIP/MIL-PRF-55681 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDACV10M7GA080-R0 | 制造商:Murata Manufacturing Co Ltd 功能描述: |
| CD-ADL2003.3.0 | 制造商:Altera Corporation 功能描述:CD-ROM ALTERA DATA |
| CDAF-10RY | 制造商:Mencom 功能描述: |
| CDAF-16N | 制造商:Mencom 功能描述: |
| CDAI-A023WJ01 | 制造商:Sharp Microelectronics Corporation 功能描述:STAND |
发布紧急采购，3分钟左右您将得到回复。