参数资料
| 型号： | CDB4207 |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 5/22页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR CS4207 |
| 标准包装： | 1 |
| 系列： | * |
| 主要目的： | 音频编解码器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | CS4207 |
| 主要属性： | 模拟输入/输出，使用 3.5mm 或 6.35mm 插孔，带现场检测 |
| 次要属性： | S/PDIF 输入和输出 |
| 已供物品： | 板 |
| 其它名称： | 598-1797 |
CDB4207
Table 1. CDB4207 HD Audio Bus Header Pinout (J1 and J9)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Signal
BCLK
GND
RST#
DVDD_IO (to J12 VL_HD header)
SYNC
GND
SDO
3.3V_DVDD_CORE (to J13 VL_IF header)
SDI0
+12V
SDI1
Key (no connection)
SDI2
3.3V_DUAL (to D12 indicator LED)
SDI3
GND
1.8
1.9
Power Supply Circuitry
The CDB4207 has several options for powering the CS4207 and auxiliary circuits. The main board power
supply can be used to power the entire board through on-board regulators. The main board power supply
can be provided by pin 10 of the HD Audio Bus header J1/J9, the PC peripheral power supply connector
J14, or an external bench supply using J8 and J7. The three options are separated via Schottky diodes, thus
the applied source with the largest voltage will be used. To use only this single power source, the CS4207
supply source selection headers (J10, J11, J12, J13, and J15) should be shunted in the ‘REG’ positions.
Alternatively each CS4207 supply can be sourced directly from external bench supplies via banana jacks
by shunting the ‘EXT’ position. In this case the main board power supply is still required to regulate a +3.3 V
supply for the S/PDIF optical jacks, the digital microphone power, and the GPIO pull-up resistors.
For the VL_HD supply ‘REG’ setting, J19 selects whether the supply is +3.3 V (unshunted) or +1.5 V (shunt-
ed). For the VD supply ‘REG’ setting, J18 selects whether the supply is +1.8 V (unshunted) or +1.5 V (shunt-
ed). For the VA supply ‘REG’ setting, J17 selects whether the supply is +5 V (unshunted), +4.7 V (1-2
shunted), +3.3 V (3-4 shunted), or +3.1V (5-6 shunted). In addition to the regulator and external options, the
CS4207’s VL_IF and VL_HD supplies can be powered directly from 3.3V_DVDD_CORE and DVDD_IO on
J1/J9 (‘HDA’), respectively, and the VA_HP supply can be powered directly from 3.3V_DVDD_CORE on
J1/J9 (‘3.3 V HDA’) or +5 V on J14 (‘5.0 V HDD’).
Note that the VL_HD supply voltage must match the chipset voltage used by the connected PC. This con-
dition is guaranteed when the ‘HDA’ setting on J12 is selected instead of ‘REG’ or ‘EXT’.
There are nine power supply indicator LEDs on the CDB4207. Each LED will be lit whenever the associated
supply is turned on. See Figure 6 on page 15 for the power supply circuit schematic and Section 3 on page
7 for the power supply connections, jumper selections, and indicator LEDs.
Grounding and Power Supply Decoupling
As with any high-performance converter, the CS4207 requires careful attention to power supply and ground-
ing arrangements to optimize performance. Figure 2 details the connections to the CS4207 and Figures 7 ,
8 , 9 , 10 , and 11 show the component placement and the board layout. The decoupling capacitors are locat-
ed as close as possible to the CS4207.
DS880DB1
5
相关PDF资料 |
PDF描述 |
|---|---|
| CDB4245 | BOARD EVAL FOR CS4245 CODEC |
| CDB42L55 | BOARD EVAL FOR CS42L55 CODEC |
| CDB44L11 | EVALUATION BOARD FOR CS44L11 |
| CDB48500-USB | KIT USB EVALUATION FOR CDB48500 |
| CDB5378 | EVALUATION BOARD FOR CS5378 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB4210 | 功能描述:音频 IC 开发工具 Eval Bd-Ultra LP HD Audio CODEC RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| CDB4215 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:16-Bit Multimedia Audio Codec |
| CDB4216 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:16-Bit Stereo Audio Codec |
| CDB4220 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:24-Bit Stereo Audio Codec with 3V Interface |
| CDB4221 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:24-Bit Stereo Audio Codec with 3V Interface |
发布紧急采购，3分钟左右您将得到回复。