- 您现在的位置：买卖IC网 > Datasheet目录855 > CM21X5R106K06AL (AVX Corporation)CAP CER 10UF 4V 10% X5R 0805 Datasheet资料下载
参数资料
| 型号： | CM21X5R106K06AL |
| 厂商： | AVX Corporation |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | CAP CER 10UF 4V 10% X5R 0805 |
| 标准包装： | 10,000 |
| 系列： | CM |
| 电容： | 10µF |
| 电压 - 额定： | 4V |
| 容差： | ±10% |
| 温度系数： | X5R |
| 安装类型： | 表面贴装，MLCC |
| 工作温度： | -55°C ~ 85°C |
| 应用： | 通用 |
| 封装/外壳： | 0805（2012 公制） |
| 尺寸/尺寸： | 0.079" L x 0.050" W（2.00mm x 1.25mm） |
| 厚度（最大）： | 0.022"（0.55mm） |
| 包装： | 带卷 (TR) |
Multilayer Ceramic Chip Capacitors
Test Conditions and Standards
Test Conditions and Specifications for High Dielectric Type (X5R, X7R)
CM/ CT/ C A Series
Test Items
Capacitance Value (C)
Tan δ (%)
Insulation Resistance (IR)
Dielectric Resistance
Appearance
Termination Strength
Bending Strength
Test Conditions
Measure after heat treatment
Capacitance Frequency Volt
C ≤ 10 μ F 1kHz ± 10% 1.0 ± 0.2Vrms
C > 10 μ F 120Hz ± 10% 0.5 ± 0.2Vrms
Measured after the rated voltage is applied for 1
minute at room ambient.
The charge and discharge current of the capacitor
must not exceed 50mA.
Apply 2.5 times of the rated voltage for 1 to 5 seconds.
The charge and discharge current of the capacitor
must not exceed 50mA.
Microscope
Apply a sideward force of 500g (5N) to a PCB-mounted sample.
note : 2N for 0201 size in for 01005 size.
Exclude CT series with thickness of less than 0.66mm.
Glass epoxy PCB: Fulcrum spacing: 90mm, duration
time 10 seconds.
Exclude CT series with thickness of less than 0.66mm.
Specifications
Within tolerance
Refer to capacitance chart
Over 10000M Ω or 500M Ω ? μ F, whichever is less
No problem observed
No problem observed
No problem observed
No significant damage at 1mm bent
Vibration
Test
Soldering
Heat
Resistance
Appearance
Δ C
Tan δ (%)
Appearance
Δ C
Tan δ (%)
IR
Take the initial value after heat treatment.
Vibration frequency: 10 to 55 (Hz)
Amplitude: 1.5mm
Sweeping condition: 10 → 55 → 10Hz/ 1 minute in X, Y and Z
Directions: 2 hours each, 6 hours total.
Take the initial value after heat treatment.
Soak the sample in 260 ° C ± 5 ° C solder for 10 ± 0.5
seconds and place in room ambient, and measure
after 24 ± 2 hours.
(Pre-heating conditions)
No problem observed
Within tolerance
Within tolerance
No problem observed
Within ± 7.5%
Within tolerance
Over 10000M Ω or 500M Ω ? μ F, whichever is less
Withstanding
Voltage
Order
1
2
Temperature
80 to 100 ° C
150 to 200 ° C
Time
2 minutes
2 minutes
Resist without problem
The charge and discharge current of the capacitor must not
exceed 50mA for IR and withstanding voltage measurement.
Soaking condition
Solderablity
Sn-3Ag-0.5Cu
Sn63 Solder
245 ± 5 ° C
235 ± 5 ° C
3 ± 0.5 sec.
2 ± 0.5 sec.
Solder coverage : 90% min.
Temperature
Cycle
Load
Humidity
Test
Appearance
Δ C
Tan δ (%)
IR
Withstanding
Voltage
Appearance
Δ C
Tan δ (%)
IR
Take the initial value after heat treatment.
(Cycle)
Room temperature (3min.) →
Lowest operation temperature (30min.) →
Room temperature (3min.) →
Highest operation temperature(30min.)
After 5 cycles, measure after 24 ± 2 hours.
The charge and discharge current of the capacitor must not
exceed 50mA for IR and withstanding voltage measurement.
Take the initial value after voltage treatment.
After applying rated voltage for 500 + 12/ ? 0 hours
in pre-condition at 40 ° C ± 2 ° C, humidity 90 to
95%RH, allow parts to stabilize for 24 ± 2 hours, at
room temperature before measurement.
The charge and discharge current of the capacitor
No problem observed
Within ± 7.5%
Within tolerance
Over 10000M Ω or 500M Ω ? μ F, whichever is less
Resist without problem
No problem observed
Within ± 12.5%
200% max. of initial value
Over 500M Ω or 25M Ω ? μ F, whichever is less
must not exceed 50mA for IR measurement.
High-
Temperature
with
Loading
Appearance
Δ C
Tan δ (%)
IR
Take the initial value after voltage treatment.
After applying twice the rated voltage at the highest
operation temperature for 1000 + 12/ ? 0 hours,
measure the sample after 24 ± 2 hours.
The charge and discharge current of the capacitor
must not exceed 50mA for IR measurement.
Apply 1.5 times when the rated voltage is 10V or less. Applied
No problem observed
Within ± 12.5%
200% max. of initial value
Over 1000M Ω or 50M Ω ? μ F, whichever is less
voltages for respective products are indicated in the below chart.
Pre-
treatment
Heat
Voltage
Keep specimen at 150 + 0/ ? 10 ℃ for 1 hour, leave specimen at room ambient for 24 ± 2 hours.
Apply the same test condition for 1 hour, then leave the specimen at room ambient for 24 ± 2 hours.
High-temperature with Loading Applied Voltage (Rated Voltage × □ )
Applied Voltage Rated Voltage
4V CT03X5R104
Products
× 1.3
× 1.5
6.3V
16V
25V
50V
CM105X5R475, CM316X5R476
CT05X5R104, CT21X5R106, CT03X5R104
CM105X7R474-105, CM21X7R105-475, CM316X7R475-106, CM32X7R106-226, CM05X5R224, CM105X5R225, CM21X5R475-106, CM316X5R226
CT105X5R105, CT21X5R225-475, CT316X5R106, CM03X5R332-103
CM105X7R474, CM21X7R105-225, CM316X7R475, CM32X7R106, CM105X5R474-105, CM21X5R225-106, CM316X5R106, CM32X5R106-226
CT316X5R225-106, CM03X5R152-103
CM21X5R105, CM32X5R106, CM32X7R106
CT21X5R225, CT316X5R105-475
100V CM32X7RK74, CM43X7R105
Please ask for individual specification for the hatched range in previous chart.
相关PDF资料 |
PDF描述 |
|---|---|
| CM453232-680KL | INDUCTOR CHIP 68UH 10% 1812 SMD |
| CMH322522-R82ML | INDUCTOR 820NH 450MA SMD |
| CMR05F101JODR | CAP MICA 100PF 500V 5% RADIAL |
| CR-1025/BN | BATTERY LITHIUM COIN 3V 10MM |
| CR-1220/HFN | BATTERY LITHIUM COIN 3V PC PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CM21X5R106K06AT | 制造商:AVX Corporation 功能描述:MLCC 0805 X5R 10U 6.3V 10% 制造商:Kyocera 功能描述:6.3V 10uF }10% 2012 |
| CM21X5R106K10AT | 制造商:AVX Corporation 功能描述:MLCC 0805 X5R 10UF 10V +-10% |
| CM21X5R106K16AT | 制造商:AVX Corporation 功能描述:MLCC 0805 X5R10U 16V 10% 制造商:KYOCERA Corporation 功能描述: |
| CM21X5R106M06AT | 制造商:AVX Corporation 功能描述:CHIP CAPACITOR |
| CM21X5R225K06AT | 制造商:AVX Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。