- 您现在的位置：买卖IC网 > PDF目录18767 > CMD-HHLR-418_ (Linx Technologies Inc)XMITTER HANDHELD 418MHZ 8 BUTTON PDF资料下载
参数资料
| 型号： | CMD-HHLR-418_ |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 6/9页 |
| 文件大小： | 0K |
| 描述： | XMITTER HANDHELD 418MHZ 8 BUTTON |
| 产品变化通告： | CMD-HHLR Discontinuation 09/Aug/2011 |
| 产品目录绘图： | Long-Range Handheld Front Long-Range Handheld Side |
| 特色产品： | OEM RF Transmitters |
| 标准包装： | 1 |
| 功能： | 发射器 |
| 调制或协议： | ASK，OOK |
| 频率： | 418MHz |
| 应用： | 通用遥控系统，车库门开启器，RKE |
| 接口： | 手持型，8 按钮 |
| 数据传输率 - 最大： | 1.2 kbps |
| 特点： | 8 按钮，1000 英尺 工作距离 |
| 电源电压： | 2.1 V ~ 3.6 V |
Connection Considerations
It is important to understand that only one transmitter at a time can be
activated within a reception area. While the transmitted signal consists
of encoded digital data, only one carrier of any particular frequency can
occupy airspace without contention at any given time. If two transmitters
are activated in the same area at the same time, then the signals will
interfere with each other and the decoder will not see a valid transmission,
so it will not take any action.
Battery Replacement
The remote unit utilizes a standard CR2032
lithium button cell. To replace the battery,
remove the access cover by pressing down
firmly on the label area and sliding it off. Once
the unit is open, remove the battery by sliding
it from beneath the holder. Replace it with
the same type of battery while observing the
polarity shown in Figure 8.
Labeling / Instruction Requirements
The transmitter has been pre-certified for FCC Part 15 and Industry Canada
license-exempt RSS standards for an intentional radiator. The 433.92MHz
version has also been tested for CE compliance for use in the European
Union. The 315MHz and 418MHz versions are not legal for use in Europe.
It has already been labeled in accordance with FCC, Industry Canada
and CE regulations. No further labeling of the unit is needed; however,
it is necessary to include the following statement in the end product’s
instruction manual or insert card. EU does not require a statement.
INSTRUCTION TO THE USER
This device complies with Part 15 of the FCC Rules and Industry Canada licence-
exempt RSS standard(s). Operation of this device is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
There may be the risk of explosion if the battery
is replaced by the wrong type.
Assembly Diagram
Battery
access
+
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
Figure 8: Battery Access
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
? Reorient or relocate the receiving antenna.
? Increase the separation between the equipment and receiver.
? Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
? Consult the dealer or an experienced radio / TV technician for help.
The user is cautioned that changes and modifications made to the equipment without
the approval of manufacturer could void the user ’s authority to operate this equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Figure 9: CMD-HHLR-***-MD Assembly
– 6 –
– 7 –
相关PDF资料 |
PDF描述 |
|---|---|
| CMD-HHCP-433 | XMITTER HANDHELD 433MHZ 8 BUTTON |
| DPC-16-55 | XFRMR PWR 115/230V 8V 110MA 1VA |
| DPC-120-8 | XFRMR PWR 115/230V 60V 16MA 1VA |
| ZVP4424A | MOSFET P-CH 240V 200MA TO92-3 |
| CMD-HHCP-315 | XMITTER HANDHELD 315MHZ 8 BUTTON |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CMD-HHLR-418_ | 功能描述:射频模块 8 Button Long Range Handhld Trans 418MHz RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| CMD-HHLR-418-MD | 功能描述:射频模块 8Btn LngRange Hndhld TX 418MHz Snap Btns RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| CMD-HHLR-418-MD_ | 功能描述:XMITTER HANDHELD 418MHZ 8 BUTTON RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:- 标准包装:5 系列:MultiModem® iCell 功能:收发器，HSPA，调制解调器 调制或协议:GPRS，GSM，EDGE 频率:850MHz，900MHz，1.8GHz，1.9GHz 应用:- 接口:RS-232，USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V，USB 其它名称:881-1125 |
| CMD-HHLR-433 | 功能描述:XMITTER HANDHELD 433MHZ 8 BUTTON RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:- 标准包装:5 系列:MultiModem® iCell 功能:收发器，HSPA，调制解调器 调制或协议:GPRS，GSM，EDGE 频率:850MHz，900MHz，1.8GHz，1.9GHz 应用:- 接口:RS-232，USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V，USB 其它名称:881-1125 |
| CMD-HHLR-433_ | 功能描述:射频模块 8 Button Long Range Handhld Trans 433MHz RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
发布紧急采购，3分钟左右您将得到回复。