- 您现在的位置：买卖IC网 > PDF目录18769 > CMD-HHTX-315 (Linx Technologies Inc)XMITTER HANDHELD 315MHZ 8 BUTTON PDF资料下载
参数资料
| 型号： | CMD-HHTX-315 |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | XMITTER HANDHELD 315MHZ 8 BUTTON |
| 产品变化通告： | CMD-HHTX-xxx Performance Change 01/Oct/2010 |
| 产品目录绘图： | CMD-HHTX-xxx |
| 标准包装： | 25 |
| 功能： | 发射器 |
| 调制或协议： | ASK，OOK |
| 频率： | 315MHz |
| 应用： | 通用遥控系统，车库门开启器，RKE |
| 接口： | 手持型，8 按钮 |
| 数据传输率 - 最大： | 1.2 kbps |
| 特点： | 8 按钮，1000 英尺 工作距离 |
| 电源电压： | 2.1 V ~ 3.6 V |
CONTENTION CONSIDERATIONS
It is important to understand that only one transmitter at a time can be activated
within a reception area. While the transmitted signal consists of encoded digital
data, only one carrier of any particular frequency can occupy airspace without
contention at any given time. If two transmitters are activated in the same area
at the same time, then the signals will interfere with each other and the decoder
will not see a valid transmission, so it will not take any action.
BATTERY REPLACEMENT
The remote unit utilizes a standard CR2032 lithium
button cell. In normal use, it will provide 1 to 2 years
of operation. To replace the battery, remove the
screw in the middle of the back cover. Once the unit
is open, remove the battery by depressing the
COMPLIANCE REQUIREMENTS
The CMD-HHTX-*** has been pre-certified by Linx for FCC Part 15 compliance
when used with an appropriate function module in keeping with the applications
allowed under section 15.231.
LABELING / INSTRUCTION REQUIREMENTS
The CMD-HHTX-*** Handheld transmitter has already been labeled in
accordance with FCC regulations in effect as of the date of this document. No
further labeling of the unit is needed; however, it is necessary to include the
following statement in the end product’s instruction manual or insert card for FCC
compliance.
release finger on the battery holder as shown.
Replace it with the same type of battery while
observing the polarity shown in the adjacent figure.
There may be the risk of explosion if the battery is
replaced by the wrong type. Replace it with the same
type of battery while observing the polarity shown in
the adjacent figure.
ASSEMBLY DIAGRAM
+
Battery Release
Figure 4: Battery Access
INSTRUCTION TO THE USER
This device complies with Part 15 of the FCC Rules.
Operation of this device is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a Class B
computing device, pursuant to FCC Rules. In order to maintain compliance with
FCC regulations, shielded cables must be used with this equipment. Operation
with non-approved equipment or unshielded cables is likely to result in
interference to radio and TV reception. The user is cautioned that changes and
modifications made to the equipment without the approval of manufacturer
could void the user’s authority to operate this equipment.
Figure 5: CMD-HHTX-*** Assembly
Place the above statement in the instruction manual or insert card.
Page 4
Page 5
相关PDF资料 |
PDF描述 |
|---|---|
| CMD-HHCP-315-MD | XMITTER HANDHELD 315MHZ 8 BUTTON |
| 241-3-20L | XFRMR PWR 115V 20VCT 0.12A LEADS |
| 241-3-16L | XFRMR PWR 115V 16VCT 0.15A LEADS |
| 241-3-12L | XFRMR PWR 115V 12.6VCT 0.20A |
| 241-3-120L | XFRMR PWR 115V 120VCT 0.02A LEAD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CMD-HHTX-418 | 功能描述:射频模块 8 Button Handheld Transmitter 418MHz RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| CMD-HHTX-433 | 功能描述:射频模块 8 Button Handheld Transmitter 433MHz RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| CMD-H-REFILL | 功能描述:电线鉴定 CABLE WIRE AND MARKR DISPENSER H REFIL RoHS:否 制造商:TE Connectivity / Q-Cees 产品:Labels and Signs 类型: 材料:Vinyl 颜色:Blue 宽度:0.625 in 长度:1 in |
| CM-DIN | 制造商:Emerson Network Power - Embedded Power 功能描述:DIN Rail Adapter; for CM Series PowerSure |
| CMDJAQLCBL | 功能描述:光纤连接器 Dupl LC Sr./Jr. 10 GbE Fiber Adapter (AQ RoHS:否 制造商:Molex 产品:Adapters 类型:8 Port with External Shutter 连接器类型:Adapter 模式:Multimode 光纤直径: 颜色:Blue 附件类型:LC Adapter |
发布紧急采购，3分钟左右您将得到回复。