- 您现在的位置：买卖IC网 > PDF目录11796 > CP2103-GM (Silicon Laboratories Inc)IC CTRLR BRIDGE USB-UART 28QFN PDF资料下载
参数资料
| 型号： | CP2103-GM |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 5/20页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR BRIDGE USB-UART 28QFN |
| 产品培训模块： | USB Protocol Products USBXpress CP21xx USB Bridge |
| 标准包装： | 73 |
| 应用： | USB |
| 接口： | USB |
| 电源电压： | 3 V ~ 3.6 V |
| 封装/外壳： | 28-VFQFN 裸露焊盘 |
| 供应商设备封装： | 28-QFN（5x5） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 627 (CN2011-ZH PDF) |
| 配用： | 336-1163-ND - KIT EVAL FOR CP2103 USB TO UART |
| 其它名称： | 336-1164 |
Rev. 1.0
13
CP2103
4. USB Function Controller and Transceiver
The universal serial bus function controller in the CP2103 is a USB 2.0 compliant full-speed device with integrated
transceiver and on-chip matching and pull-up resistors. The USB function controller manages all data transfers
between the USB and the UART as well as command requests generated by the USB host controller and
commands for controlling the function of the UART.
The USB Suspend and Resume signals are supported for power management of both the CP2103 device as well
as external circuitry. The CP2103 will enter Suspend mode when Suspend signaling is detected on the bus. Upon
entering Suspend mode, the CP2103 asserts the SUSPEND and SUSPEND signals. SUSPEND and SUSPEND
are also asserted after a CP2103 reset until device configuration during USB Enumeration is complete.
The CP2103 exits the Suspend mode when any of the following events occurs: (1) Resume signaling is detected or
generated, (2) a USB Reset signal is detected, or (3) a device reset occurs. Upon exit from Suspend mode, the
SUSPEND and SUSPEND signals are de-asserted.
Both SUSPEND and SUSPEND temporarily float high during a CP2103 reset. If this behavior is undesirable, a
strong pulldown (10 k
) can be used to ensure SUSPEND remains low during reset. See Figure 6 for other
recommended options.
Figure 6. Typical Connection Diagram
Option 1: A 4.7 k
pull-up resistor can be added to increase noise immunity.
Option 2: A 4.7 F capacitor can be added if powering other devices from the on-chip regulator.
Option 3: Avalanche transient voltage suppression diodes should be added for ESD protection .
Option 3: Use Littlefuse p/n SP0503BAHT or equivalent.
Option 4: 10 k
resistor to ground to hold SUSPEND low on initial power on or device reset.
1
CP2103
SUSPEND
11
12
REGIN
7
GND
2
RST
9
D+
3
D-
4
8
C2
0.1
F
C1
1
F
RI
DCD
CTS
RTS
RXD
TXD
DSR
DTR
1
28
27
26
25
24
23
22
2
3
External RS-232
transceiver or
UART circuitry
(to external circuitry
for USB suspend
states)
VBUS
D-
D+
GND 4
5
6
USB
CONNECTOR
6
VDD
VBUS
VDD
R1
4.7 k
D1
D2
D3
Option 1
R2
10 k
Option 4
Option 3
C4
4.7
F
Option 2
VIO
5
1
F
I/O Voltage
GPIO.3
GPIO.2
GPIO.1
GPIO.0
19
18
17
16
External
Application
Circuitry
相关PDF资料 |
PDF描述 |
|---|---|
| CP2101-GM | IC CTRLR BRIDGE USB-UART 28MLP |
| 1604059-2 | KIT,350A,2/0 AWG,ORANGE |
| 1604059-1 | KIT,350A,2/0 AWG,YELLOW |
| 1604045-4 | KIT,175A,1 AWG,GRAY |
| MS3106F20-22S | CONN PLUG 6POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CP2103-GMR | 功能描述:输入/输出控制器接口集成电路 USB-TO-UART BRIDGE RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| CP2104 | 制造商:SILABS 制造商全称:SILABS 功能描述:USB DRIVER CUSTOMIZATION |
| CP2104EK | 功能描述:界面开发工具 Evaluation kit RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| CP2104-F03-GM | 功能描述:输入/输出控制器接口集成电路 USB to UART bridge RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| CP2104-F03-GMR | 功能描述:输入/输出控制器接口集成电路 USB to UART bridge RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。