参数资料
| 型号： | CP2105EK |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 4/10页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR CP2105 |
| 产品培训模块： | CP21xx USB Bridge |
| 标准包装： | 1 |
| 主要目的： | 接口，USB 2.0 至 UART（RS485）电桥 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | CP2105 |
| 主要属性： | 全速（12Mbps） |
| 次要属性： | LED 状态指示器 |
| 已供物品： | 板，线缆，CD |
| 相关产品： | 336-2009-5-ND - IC SGL USB-DL UART BRIDGE 24QFN |
| 其它名称： | 336-2005 |
CP2105-EK
6. Target Board
The CP2105 Evaluation Kit includes an evaluation board with a CP2105 device preinstalled for evaluation and pre-
liminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping using
the evaluation board. Refer to Figure 3 for the locations of the various I/O connectors.
P1
P2
P3
J1
J2, J3
J4
J6
J7, J8
DSS–DS4
DS5
USB connector for USB interface
DB9 connector for Standard RS232 interface
DB9 connector for Enhanced RS232 interface
Enhanced UART signal access connector
GPIO access connector
Power connector
Standard UART signal access connector
SUSPEND LED source connector
Green GPIO LEDs
Red SUSPEND indicator LED
CP2105-EK
J6
J2
P3
RS232
Transceiver
Enhanced
Pin 2
Pin 1
DS0
DS1
P1
______
J7
J8
CP2105
SUSPEND LED
DS5
P2
RS232
Transceiver
Pin 1
J3
Standard
Pin 2
J1
J4
DS2
DS3
DS4
Figure 3. CP2105 Evaluation Board with Default Shorting Blocks Installed
6.1. LED Headers (J2, J3)
Connectors J2 and J3 are provided to allow access to the GPIO pins on the CP2105 when in GPIO mode. Place
shorting blocks on J2 and J3 to connect the GPIO pins to the five green LEDs DS0–DS4. These LEDs can be used
to indicate active communications through the CP2105. Table 1 shows the LED corresponding to each header
position. When using the CP2105 in Modem mode, the shorting blocks on J2 and J3 should be removed.
Table 1. J2 and J3 LED Locations
4
LED
DS0
DS1
DS2
DS3
DS4
Pins
J2[1:2]
J2[3:4]
J3[1:2]
J3[3:4]
J3[5:6]
Rev. 0.5
相关PDF资料 |
PDF描述 |
|---|---|
| CP881 | CONN BNC PLUG CRIMP RG-58 |
| CP882 | CONN BNC PLUG CRIMP RG-59,62 |
| CPC2400E-EVAL | MODULE MODEM 2400BAUD EMBEDDEDED |
| CPF-56-ALX | CONN F PLUG CRIMP TRI-SHLD RG-6 |
| CPFI-UG88-10 | CONN BNC PLUG TWIST-ON |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CP2105-F01-GM | 功能描述:输入/输出控制器接口集成电路 USB to Dual UART bridge RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| CP2105-F01-GMR | 功能描述:输入/输出控制器接口集成电路 USB to Dual UART bridge RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| CP2105-F05-GMR | 制造商:Silicon Laboratories Inc 功能描述:USB TO DUAL UART BRIDGE - Tape and Reel |
| CP2105-GM | 制造商:SILABS 制造商全称:SILABS 功能描述:Data format: 8 data bits, 1 stop bit Parity: Even, Pdd, No parity Baud rates: 2400 bps to 921600 bps |
| CP2108-B01-GM | 功能描述:输入/输出控制器接口集成电路 USB to QUAD UART RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。