参数资料
| 型号： | CP82C55A-5Z |
| 厂商： | Intersil |
| 文件页数： | 6/29页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER 24B 40DIP |
| 标准包装： | 99 |
| 接口： | 可编程 |
| 输入/输出数： | 24 |
| 中断输出： | 无 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 40-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 40-DIP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
14
FN2969.10
November 16, 2006
Special Mode Combination Considerations
There are several combinations of modes possible. For any
combination, some or all of Port C lines are used for control
or status. The remaining bits are either inputs or outputs as
defined by a “Set Mode” command.
During a read of Port C, the state of all the Port C lines,
except the ACK and STB lines, will be placed on the data
bus. In place of the ACK and STB line states, flag status will
appear on the data bus in the PC2, PC4, and PC6 bit
positions as illustrated by Figure 17.
Through a “Write Port C” command, only the Port C pins
programmed as outputs in a Mode 0 group can be written.
No other pins can be affected by a “Write Port C” command,
nor can the interrupt enable flags be accessed. To write to
any Port C output programmed as an output in Mode 1
group or to change an interrupt enable flag, the “Set/Reset
Port C Bit” command must be used.
With a “Set/Reset Port C Bit” command, any Port C line
programmed as an output (including IBF and OBF) can be
written, or an interrupt enable flag can be either set or reset.
Port C lines programmed as inputs, including ACK and STB
lines, associated with Port C are not affected by a “Set/Reset
Port C Bit” command. Writing to the corresponding Port C bit
positions of the ACK and STB lines with the “Set Reset Port
C Bit” command will affect the Group A and Group B
interrupt enable flags, as illustrated in Figure 17.
Current Drive Capability
Any output on Port A, B or C can sink or source 2.5mA. This
feature allows the 82C55A to directly drive Darlington type
drivers and high-voltage displays that require such sink or
source current.
Reading Port C Status (Figures 15 and 16)
In Mode 0, Port C transfers data to or from the peripheral
device. When the 82C55A is programmed to function in
MODE DEFINITION SUMMARY
MODE 0
MODE 1
MODE 2
IN
OUT
IN
OUT
GROUP A ONLY
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
In
Out
In
Out
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
In
Out
In
Out
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
In
Out
INTRB
IBFB
STBB
INTRA
STBA
IBFA
I/O
INTRB
OBFB
ACKB
INTRA
I/O
ACKA
OBFA
I/O
INTRA
STBA
IBFA
ACKA
OBFA
Mode 0
or Mode 1
Only
INPUT CONFIGURATION
D7
D6
D5
D4
D3
D2
D1
D0
I/O
IBFA
INTEA INTRA INTEB
IBFB
INTRB
OUTPUT CONFIGURATION
D7
D6
D5
D4
D3
D2
D1
D0
OBFA INTEA
I/O
INTRA INTEB
OBFB INTRB
FIGURE 15. MODE 1 STATUS WORD FORMAT
D7
D6
D5
D4
D3
D2
D1
D0
OBFA
INTE1
IBFA
INTE2 INTRA
X
(Defined by Mode 0 or Mode 1 Selection)
FIGURE 16. MODE 2 STATUS WORD FORMAT
GROUP A
GROUP B
GROUP A
GROUP B
GROUP A
GROUP B
82C55A
相关PDF资料 |
PDF描述 |
|---|---|
| CS82C55AZ96 | IC I/O EXPANDER 24B 44PLCC |
| 5-531250-4 | CONN CARD EDGE BOARD RETAINER |
| 583691-2 | RET SPG |
| PCA9698DGG,512 | IC I/O EXPANDER I2C 40B 56TSSOP |
| PCA9506DGG,512 | IC I/O EXPANDER I2C 40B 56TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CP82C55AR2489 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CP82C55AS2065 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CP82C55AS2529 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CP82C55AS2580 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CP82C55AZ | 功能描述:外围驱动器与原件 - PCI W/ANNEAL PERIPH PRG- I/O5V8MHZ40PDIPCOM RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。