- 您现在的位置：买卖IC网 > PDF目录1908 > CPC1465M (IXYS Integrated Circuits Division)IC SHDSL/ISDN DC TERM 16MLP PDF资料下载
参数资料
| 型号： | CPC1465M |
| 厂商： | IXYS Integrated Circuits Division |
| 文件页数： | 2/15页 |
| 文件大小： | 0K |
| 描述： | IC SHDSL/ISDN DC TERM 16MLP |
| 标准包装： | 52 |
| 功能： | DC 信号终端 |
| 接口： | ISDN，SHDSL |
| 电路数： | 1 |
| 功率（瓦特）： | 1W |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WDFN 裸露焊盘 |
| 供应商设备封装： | 16-MLP（7x6） |
| 包装： | 管件 |
| 包括： | 光耦合器 |
INTEGRATED CIRCUITS DIVISION
CPC1465
10
www.ixysic.com
R04
2. Functional Description
2.1 Introduction
The CPC1465 can be used for a number of designs
requiring a dc hold circuit such as SHDSL modem and
ISDN NT1 terminal applications. Typical SHDSL
applications will use a circuit design similar to the one
Diagram” on page 9 while the typical ISDN NT1 circuit
design will be similar to the one shown in Figure 10
The DC Termination IC performs two functions in an
ISDN NT1 terminal; as an electronic inductor providing
a low impedance dc termination with a high
impedance ac termination, and second as part of the
dc signalling system for automated line testing
capability. The CPC1465 meets or exceeds the
requirements for an NT1 dc termination as described
in ANSI T1.601-1991.
Whereas the SHDSL modem application does not
have a signalling requirement, the signaling function
provides an excellent method to monitor for the loss of
sealing current. Generally, loss of sealing current in an
SHDSL application indicates loop loss.
As can be seen in the application circuit in Figure 1 on
page 1, CPC1465 designs require few external
components. For the most basic design, all that is
needed is a circuit protector, two resistors and a
capacitor.
2.2 Surge Protection
Although the CPC1465 is current limited, it is not an
over-voltage surge protector. To protect the CPC1465
against destructive over-voltage transients, IXYS
Integrated Circuits Division recommends the use of a
crowbar-type surge protector that limits the surge
voltage seen by the CPC1465 to 250 V. The protection
device must be able to withstand the surge
requirements specified by the appropriate governing
agency in regions where the product will be deployed.
Teccor, Inc. and Bourns, Inc. make suitable surge
protectors for most applications. Devices such as
Teccor’s P1800SC or P2000SC Sidactors and Bourns’
TISP4220H3 or TISP4240H3 thyristors should provide
suitable protection.
2.3 Bridge Rectifier
The bridge rectifier in the CPC1465 ensures that the
device is polarity insensitive and provides consistent
operational characteristics if the tip and ring leads are
reversed.
2.4 State Transitions
The dc tip to ring voltage-current characteristics of the
CPC1465 are shown in Figure 2 “I-V Requirements
Transition timings are illustrated in Figure 7 “Applied
configuration for these timings is given in Figure 6
timing figures are located on page 7.
State transition timings are set by the 1
F capacitor
connected between the TC and COM pins.
2.4.1 Activation - On-State
Application of battery voltage to the loop causes the
CPC1465 to conduct whenever the voltage exceeds
approximately 35 V. With application of sufficient
voltage applied across the tip and ring terminals, the
CPC1465 will initially conduct a nominal 150
A of
sealing current for approximately 20 ms prior to
activation. Once activated, the CPC1465 will remain in
the on state for as long as the loop current exceeds a
nominal 0.5 mA.
The CPC1465 turn-on timing circuit assures device
activation will occur within 50 ms of an applied voltage
greater than 43.5 V but not within the first 3 ms.
2.4.2 Deactivation - Off-State
While the CPC1465 activation protocol is based on an
initial minimum voltage level, deactivation is based on
a diminished sealing current level. Deactivation occurs
when the nominal sealing current level drops below
0.5 mA with guaranteed deactivation occurring for
sealing current levels less than 0.1 mA
相关PDF资料 |
PDF描述 |
|---|---|
| CPC2400E | MODULE MODEM 2400BAUD EMBEDDEDED |
| CPC5601D | IC DRVR PROGRAMMABLE 16-SOIC |
| CPC5710N | IC PHONE LINE MONITOR 8-SOIC |
| CPC5712U | PHONE LINE MON W/DETECTOR 16QSOP |
| CPC7220W | IC ANALOG SWITCH 8CH HV 28-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CPC1465MTR | 功能描述:固态继电器-PCB安装 DC Termination IC RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| CPC1466 | 制造商:CLARE 制造商全称:Clare, Inc. 功能描述:Broadband ADSL/VDSL DC Termination IC |
| CPC1466D | 功能描述:电信线路管理 IC DC TERMINATION IC RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| CPC1466DTR | 功能描述:电信线路管理 IC DC TERMINATION IC, TAPE/REEL RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| CPC1466M | 制造商:CLARE 制造商全称:Clare, Inc. 功能描述:Broadband ADSL/VDSL DC Termination IC |
发布紧急采购，3分钟左右您将得到回复。