- 您现在的位置：买卖IC网 > PDF目录1786 > CPC1580P (IXYS Integrated Circuits Division)OPTOCOUPLER 2.5MA 8-PIN FLTPCK PDF资料下载
参数资料
| 型号： | CPC1580P |
| 厂商： | IXYS Integrated Circuits Division |
| 文件页数： | 7/13页 |
| 文件大小： | 0K |
| 描述： | OPTOCOUPLER 2.5MA 8-PIN FLTPCK |
| 标准包装： | 50 |
| 电压 - 隔离： | 3750Vrms |
| 通道数： | 1，单向 |
| 电流 - DC 正向(If)： | 1mA |
| 输入类型： | DC |
| 输出类型： | 栅极驱动器 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SMD，鸥翼型 |
| 供应商设备封装： | 8-扁平封装 |
| 包装： | 管件 |
I NTEGRATED C IRCUITS D IVISION
Where V CAP > 15V and Q G is the total gate charge
(listed in the MOSFET data sheet).
The storage capacitor needs to deliver enough charge
to the gate without going below the 15V required for
switching the MOSFET. This means that V LOAD must
equal, at a minimum, 15.7V. The part can operate at a
lower voltage, but the MOSFETs will be turned on
slowly.
The proper selection of a capacitor is important. The
rated voltage should be at least two to three times the
V CAP . The extra margin is important because some
capacitors lose capacitance when operated at their full
rated voltages. When selecting a capacitor, be sure to
add in their tolerance because of capacitor drift. For
example:
? C ST = 1 ? F, 20% tolerance; V CAP = 15V
? 1 ? F x 20% = 0.2 ? F
? 1 ? F + 0.2 ? F = 1.2 ? F
Capacitance drift can also be due to temperature and
the dielectrics used. Therefore, the required capacitor
value is 1 ? 2 ? F or next higher value, and the capacitor
voltage rating must be at least 30 volts. It is
recommended to go higher in the voltage rating if
engineering restraints permit, such as 50V.
Temperature requirements for capacitors are
application-specific. The designer must know the
intended operating temperature when selecting
capacitors. The information given above should be
applied to other capacitors discussed in this data
sheet.
The CPC1580 can deliver 32nC at the rated operating
speed and will operate with much larger loads (>4 ? F)
with slower turn-on and turn-off times.
Note: Care must be taken to minimize any
capacitor-to-ground leakage current path
between pins 7 and 8 (MOSFET gate current)
and between pins 5 and 6. Leakage currents will
discharge the storage capacitor and, even
though the device is already on, will become a
load to the photocurrent, which keeps the gate
CPC1580
4.3 Transistor Selection
The CPC1580 charges and discharges an external
MOSFET transistor. The selection of the MOSFET is
determined by the user to meet the specific power
requirements for the load. The CPC1580 output
voltage is listed in the specifications, but as mentioned
earlier, there must be little or no gate leakage.
Another parameter that plays a significant role in the
selection of the transistor is the gate drive voltage
available from the part. The CPC1580 uses
photovoltaic cells to collect the optical energy
generated by the LED; to generate more voltage, the
photovoltaic diodes are stacked. The voltage change
of the photovoltaic stack reduces with increased
temperature. The user must select a transistor that will
maintain the load current at the maximum
temperature, given the V GS in Section 1.7 , the
CPC1580 Table of Electrical Specifications.
use “logic level” MOSFETs for each design to maintain
the load described.
4.3.1 Transistor Switching Characteristics
The primary characteristics of the application
switching are t on , t off , t RISE , t FALL , and the recovery
time of the storage capacitor, t CHG . These parameters
are dependent on the MOSFET selection and need to
be reviewed in light of the application requirements.
The CPC1580 turns on the MOSFET transistor to the
specified V GS after the t on delay. Similarly the t off delay
is the amount of time until the LED is turned off and
the capacitive load discharges to the level in the
CPC1580 specification. For MOSFETs with larger or
smaller required gate charge the t on and t off will be
proportionately faster and slower, but it is not a linear
relationship.
To calculate the nominal rise time of the transistor's
drain voltage, V D :
voltage on. The gate voltage will be reduced if
>500nA of leakage is present, therefore the
combined impedance from pin 8 to pin 7, pin 5,
t RISE,VD
~
V LOAD ? C RSS
I G_SINK
(SECONDS)
and pin 6, capacitor current, and MOSFET
current must be >20M ? over the temperature
rating of the part.
To calculate the nominal fall time of the transistor's
drain voltage, V D :
t FALL,VD ~
V LOAD ? C RSS
I G_SOURCE
(SECONDS)
R01
www.ixysic.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| CPC5902GS | ISOLAT 3.75KVRMS 2CH BIDIR 8SMD |
| CPC5903GSTR | ISOL 3.75KVRMS 1CH BIDIR 8-SMD |
| CS1601-FSZ | IC PFC CONTROLLER BALLAST 8SOIC |
| CS2001YDWFR20 | IC REG BST FLYBK ADJ 1.2A 20SOIC |
| CS2841BEDR14G | IC REG CTRLR BST FLYBK CM 14SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CPC1580PTR | 功能描述:逻辑输出光电耦合器 Optically Isolated Gate Driver, Tape/Reel RoHS:否 制造商:Fairchild Semiconductor 绝缘电压:4243 Vrms 输出类型:Push-Pull 最大传播延迟时间:500 ns 最大正向二极管电压: 最大反向二极管电压: 最大正向二极管电流: 最大连续输出电流:2.5 A 最大功率耗散:100 mW 最大工作温度:+ 100 C 最小工作温度:- 40 C 封装 / 箱体:SO-16 封装:Tube |
| CPC1590 | 制造商:CLARE 制造商全称:Clare, Inc. 功能描述:Optically Isolated Gate Drive Circuit |
| CPC1590P | 功能描述:逻辑输出光电耦合器 Optically Isolated Gate Driver RoHS:否 制造商:Fairchild Semiconductor 绝缘电压:4243 Vrms 输出类型:Push-Pull 最大传播延迟时间:500 ns 最大正向二极管电压: 最大反向二极管电压: 最大正向二极管电流: 最大连续输出电流:2.5 A 最大功率耗散:100 mW 最大工作温度:+ 100 C 最小工作温度:- 40 C 封装 / 箱体:SO-16 封装:Tube |
| CPC1590PTR | 功能描述:逻辑输出光电耦合器 Optically Isolated Gate Driver, Tape/Reel RoHS:否 制造商:Fairchild Semiconductor 绝缘电压:4243 Vrms 输出类型:Push-Pull 最大传播延迟时间:500 ns 最大正向二极管电压: 最大反向二极管电压: 最大正向二极管电流: 最大连续输出电流:2.5 A 最大功率耗散:100 mW 最大工作温度:+ 100 C 最小工作温度:- 40 C 封装 / 箱体:SO-16 封装:Tube |
| CPC1593 | 制造商:IXYS 制造商全称:IXYS Corporation 功能描述:Single-Pole, Normally Open OptoMOS?? Relay Integrated Current Limit with Voltage and Thermal Protection |
发布紧急采购，3分钟左右您将得到回复。