- 您现在的位置：买卖IC网 > PDF目录26506 > CPC5712U (CLARE INC) PDF资料下载
参数资料
| 型号： | CPC5712U |
| 厂商： | CLARE INC |
| 元件分类： | 通信及网络 |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO16 |
| 封装： | ROHS COMPLIANT, QSOP-16 |
| 文件页数： | 7/10页 |
| 文件大小： | 387K |
| 代理商： | CPC5712U |
CPC5712
6
www.clare.com
R00G
will be larger than the threshold set at VL2. As an
example, the voltage at VL2 represents a |TIP/RING|
threshold of 20V and VH2 represents a TIP/RING
threshold of 22V. DET2 will be low if the |TIP/RING|
voltage decreases below 20V, and it will remain low
until the |TIP/RING| voltage increases above 22V.
DET2 will change states for both positive and negative
values of TIP/RING voltage as represented by
|TIP/RING|. This means that DET2 will also be low if
the TIP/RING voltage decreases below -20V and will
remain low until the TIP/RING voltage increases
beyond -22V. The user must rely on POLARITY to
determine whether the TIP/RING threshold changed
due to a positive or negative differential signal since
DET2 does not contain any polarity information.
DET1 behaves similarly to DET2, except that it is
triggered based on the voltage set at VL1 and VH1.
This means that DET1 will be low after the |TIP/RING|
voltage has decreased below the value set by the
voltage at VL1 and will not change high until after the
|TIP/RING| voltage has increased above the value set
by the voltage at VH1. DET1 does not give any polarity
information for the same reasons as defined for DET2.
In the application circuit provided, the TIP/RING
threshold levels of DET2 will always be higher than the
threshold levels of DET1.
2.5 Detector Threshold Operation
VL1, VH1, VL2, and VH2: Inputs used to set the
|TIP/RING| threshold levels that are to be detected.
VH1 and VL1 are used to set the high and low threshold
levels. The difference between VH1 and VL1 sets the
hysteresis for the 1st threshold level. VH2 and VL2 are
used to set the threshold and hysteresis for the 2nd
threshold level. There is a digital output for both the 1st
and 2nd threshold levels that shows when the
|TIP/RING| voltage has crossed a threshold level and
when it has exceeded the configured hysteresis level.
This was explained in the DET1 and DET2 definitions.
In general, the digital output will be low when the
|TIP/RING| voltage has fallen below the VL# level and
will change high again once the |TIP/RING| voltage
has risen above the VH# level.
VREF: An analog output that is similar to the DC bias
level that is applied to OUT+ and OUT-. This voltage is
brought off chip so that it can be used to define
threshold detection levels. Load capacitance on this
pin must be kept less than the value recommended in
the table Recommended Operating Conditions.
The total load resistance on this pin must be within the
range specified in the table Recommended
Resistors R1, R2, R3, R4 and R5 are external
resistors, which must be provided by the user. The
selection of the resistors determines the voltages at
VL2, VH2, VL1 and VH1 and therefore the threshold and
hysteresis values for the 2 detectors.
The values for R1, R2, R3, R4, and R5 are easily
determined. Select voltage levels for the 1st and 2nd
threshold and hysteresis settings such that:
VH2 > VL2 > VH1 > VL1
Then use the following algorithm to find the values of
R2, R3, R4 and R5.
1.
Select a value for R1.
2.
R2 = (R1(VH1-VL1)) / VL1
3.
R3 = (R1(VL2-VH1))/ VL1
4.
R4 = (R1(VH2-VL2)) / VL1
5.
R5 = (R1(VREF/A-VH2)) / VL1
V
REF = 1.5V
A = (2.5 (R
DIFF)) / (RIN1 + RIN2 + RDIFF), which
typically calculates to 0.05; in this case: 0.04938.
See Figure 2.
Also, as shown in the table of Recommended
Operating Conditions, the resistive load on the VREF
pin must fall within the range:
20k
< (R1 + R2 + R3 + R4 + R5) < 1M
2.6 Power Connections
VCC, Ground: Power supply pins. These are used to
supply voltage and ground to the chip.
相关PDF资料 |
PDF描述 |
|---|---|
| CPC7220K | |
| CPC7220KTR | |
| CPC7220WTR | |
| CPC7232WTR | |
| CPC7232W | |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CPC5712UTR | 功能描述:固态继电器-PCB安装 Phone Line Monitor,T/R RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| CPC5750U | 功能描述:Telecom IC CODEC 24-SSOP 制造商:ixys integrated circuits division 系列:- 包装:管件 零件状态:有效 功能:CODEC 接口:SPI 电路数:1 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:7.5mA 功率（W）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-SSOP（0.154"，3.90mm 宽） 供应商器件封装:24-SSOP 包括:- 标准包装:50 |
| CPC5750UTR | 功能描述:IC VOICE BAND CODEC 24SSOP 制造商:ixys integrated circuits division 系列:- 包装:带卷（TR） 零件状态:在售 功能:CODEC 接口:SPI 电路数:1 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:7.5mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-SSOP（0.154"，3.90mm 宽） 供应商器件封装:24-SSOP 包括:- 标准包装:2,000 |
| CPC5902G | 功能描述:ISOLAT 3.75KVRMS 2CH BIDIR 8DIP RoHS:是 类别:隔离器 >> 光隔离器 - 逻辑输出 系列:- 标准包装:1,000 系列:- 电压 - 隔离:3750Vrms 通道数:1，单向 电流 - 输出 / 通道:50mA 数据速率:15MBd 传输延迟高 - 低 @ 如果:50ns @ 7.5mA 电流 - DC 正向(If):20mA 输入类型:DC 输出类型:开路集电极 安装类型:表面贴装 封装/外壳:8-SMD，鸥翼型 供应商设备封装:8-DIP 鸥翼型 包装:带卷 (TR) |
| CPC5902G_5903G-EVAL | 功能描述:CPC5902, CPC5903 - Interface, Buffer/Repeater Evaluation Board 制造商:ixys integrated circuits division 系列:- 零件状态:有效 主要用途:接口，缓冲器/中继器 嵌入式:- 使用的 IC/零件:CPC5902，CPC5903 主要属性:隔离 辅助属性:- 所含物品:板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。