- 您现在的位置：买卖IC网 > PDF目录19394 > CPC9909N (IXYS Integrated Circuits Division)IC LED DRVR HIGH BRIGH SOIC-8 PDF资料下载
参数资料
| 型号： | CPC9909N |
| 厂商： | IXYS Integrated Circuits Division |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR HIGH BRIGH SOIC-8 |
| 应用说明： | CPC9909 Design Considerations |
| 产品目录绘图： | High Brightness LED Driver |
| 特色产品： | CPC9909 LED Driver |
| 标准包装： | 100 |
| 恒定电流： | 是 |
| 拓扑： | 交直流离线开关，PWM |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 背光，通用 |
| 类型 - 次要： | 高亮度 LED（HBLED），RGB |
| 频率： | 30kHz ~ 120kHz |
| 电源电压： | 8 V ~ 550 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | CLA330 |
V CS ? high ?
I LED + 0.5 ? I L
V CS ? high ?
1.15 ? I LED
I NTEGRATED C IRCUITS D IVISION
2.3 Input Voltage Regulator
The CPC9909 has an internal voltage regulator that
can work with input voltages ranging from 12V DC to
550V DC . When a DC voltage greater than 12V is
applied at the V I N pin, the internal voltage regulator
regulates the voltage down to a typical 7.8V. The V DD
pin is the internal voltage regulator output pin and
must be bypassed by a low-ESR capacitor to provide
a low impedance path for high frequency switching
noise.
The CPC9909 driver does not require the bulky
start-up resistors typically needed for off-line
controllers. The internal voltage regulator provides
sufficient voltage and current to power internal IC
circuits. This voltage is also available at the V DD pin,
and can be used as a bias voltage for external
circuitry.
The internal voltage regulator can be bypassed by
applying an external DC voltage to the V DD pin that is
slightly higher than the internally generated regulator
voltage. This reduces the power dissipation of the
integrated circuit, and it is more suitable in isolated
applications where an auxiliary winding can be used to
drive the V DD pin.
The total input current drawn from the V I N pin is equal
to the quiescent current drawn by the internal circuitry
(which is specified at 0.6mA maximum) plus the gate
driver current. See “Shut-Down Mode Supply Current”
The current draw of the gate driver depends on the
switching frequency and the gate charge of the
external power MOSFET. The total input current can
be calculated by:
I IN ? 0.6 mA + ? Q GATE ? f S ?
Where Q GATE is the total gate charge of the MOSFET
and f S is the oscillator external frequency.
2.4 Current Sense Resistor
The peak LED current is set by an external sense
resistor (R SE N SE ) connected from the CS pin to
ground.
The value of the current sense resistor is calculated
based on the average LED current desired, the current
sense threshold, and the inductor ripple current.
CPC9909
The peak-to-peak difference in the inductor current
waveform is referred to as inductor ripple current (the
inductor is typically selected to be large enough to
keep this ripple within 30% of the average). Factor in
the ripple current when calculating the sense resistor.
The current sense resistor value can be found by:
R SENSE = ----------------------------------
Where:
? V CS(high) = current sense threshold =0.25V (or V LD )
? I LED = average LED/inductor current
? ? I L = inductor ripple current = 0.3*I LED
Combining terms:
R SENSE = ----------------------------
2.5 Current Sense Blanking
The CPC9909 has an internal current sense blanking
circuit. When the power MOSFET is turned on, the
external inductor can cause an undesired spike at the
current sense pin, initiating a premature termination of
the gate pulse. To avoid this condition, a typical 400ns
internal leading edge blanking time is implemented,
thereby eliminating the need for external RC filtering,
and simplifying the design. During the current sense
blanking time, the current limit comparator is disabled,
preventing the gate-drive circuit from terminating the
gate-drive signal.
2.6 Enable/Disable Function
Connecting the PWMD pin to V DD enables the gate
driver. Connecting PWMD to G N D disables the gate
driver and sets the device in standby mode. In standby
mode, the quiescent current is 0.6mA maximum.
2.7 Minimum Off-Time One-Shot
The CPC9909 uses a fixed off-time control scheme.
The minimum off-time is set by an external resistor
connected between the RT and G N D terminals.
The off-time can be determined by:
t off ? ? s ? = ? ? ? R T ? k ? ? ? ? 66 ? + 0.8 ?
Off-time selection indirectly determines the switching
frequency of the LED driver.
R04
www.ixysic.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6505UTP100+T | IC TEMP SWITCH DL TRIP SOT23-6 |
| ESC49DRTI-S734 | CONN EDGECARD 98POS DIP .100 SLD |
| MAX6505UTP070+T | IC TEMP SWITCH DL TRIP SOT23-6 |
| ADSP-BF532SBBC400 | IC DSP CTLR 16B 400MHZ 160CSPBGA |
| HSC36DRYI-S13 | CONN EDGECARD 72POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CPC9909NE | 功能描述:LED照明驱动器 8V-550V 2.5W RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CPC9909NETR | 功能描述:LED照明驱动器 8V-550V 2.5W RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CPC9909NTR | 功能描述:LED照明驱动器 8V-550V 2.5W RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CPC9R6D | 制造商:CORNELL DUBILIER ELECTRONICS 功能描述:Cap Ceramic 9.6pF 1000V C0G 0.5pF (6 X 4.5mm) Radial 6.4mm 125°C |
| CPCAV16472 | 制造商:Distributed By MCM 功能描述:HDMI To Screw Terminal Module |
发布紧急采购，3分钟左右您将得到回复。