参数资料
型号: CS1301-9ERD0TB2
厂商: POWER-ONE INC
元件分类: 电源模块
英文描述: 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
封装: METAL, CASE S02, MODULE
文件页数: 4/33页
文件大小: 438K
代理商: CS1301-9ERD0TB2
S Series Data Sheet
100 Watt AC-DC and DC-DC Converters
APR 26, 2006 revised to SEP 25, 2006
Page 12 of 33
www.power-one.com
Fig. 15
Typical output response as a function of inhibit control
Table 5: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
Vinh Inhibit Vo = on Vi min - Vi max –50
0.8
V
voltage
Vo = off
2.4
50
Iinh Inhibit current
Vinh = 0
–400
A
tr
Rise time
30
ms
tf
Fall time
depending on
Io
0
t
0
Inhibit
1
0.1
1
Vo/Vo nom
tr
tf
06001
Sense Lines
(Only single output models)
Important: Sense lines must always be connected! Incorrectly
connected sense lines may activate the overvoltage limitation,
resulting in a permanent short-circuit of the output.
This feature allows for compensation of voltage drops across the
connector contacts and if necessary, across the load lines. If the
sense lines are connected at the load rather than directly at the
connector, the user should ensure that the voltage differences
specified in the table below are not exceeded. We recommend
connecting the sense lines directly at the female connector.
To ensure correct operation, both sense lines (S+ and S–) should
be connected to their respective power outputs (Vo1+ and Vo1–)
and the voltage difference between any sense line and its
respective power output pin (as measured on the connector)
should not exceed the following values:
Table 6: Maximum voltage compensation allowed using
sense lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
< 0.5 V
< 0.25 V
12, 15, 24 V
< 1.0 V
< 0.25 V
If the output voltages are increased above Vo nom via the R-input
control, option P setting, remote sensing or option T, the output
currents must be reduced accordingly so that Po nom is not
exceeded.
Auxiliary Functions
i Inhibit for Remote On and Off
Note: With open i input the output is disabled.
The outputs may be enabled or disabled by means of a logic
signal (TTL, CMOS, etc.) applied between the inhibit input i and
the negative pin of output 1 (Vo1–). In systems with several
converters, this feature can be used to control the activation
sequence of the converters. If the inhibit function is not required,
connect the inhibit pin 18 to pin 14 to enable the outputs (active
low logic, fail safe).
Vi+
Vi–
Vo–
i
Vo+
Iinh
Vinh
06031
1.6
0.8
0
–0.8
–50
Vinh [V]
Iinh [mA]
–30
0
–10
10
30
50
2.0
1.2
0.4
–0.4
Vinh = 0.8 V
Vo = on
Vo = off
Vinh = 2.4 V
06032
Fig. 13
Definition of Vinh and Iinh.
Fig. 14
Typical inhibit current Iinh versus inhibit voltage Vinh
相关PDF资料
PDF描述
CS1501-7EPD9B2 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
CS1501-7RD9TB2 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
CS1501-9EPD2TB2 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
CS1501-9EPD3B2 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
CS1501-9PD3B2 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
相关代理商/技术参数
参数描述
CS13035 制造商:UNBRANDED 功能描述:HEADSET + MIC FOLDABLE
CS13-04GO4 制造商:未知厂家 制造商全称:未知厂家 功能描述:Netzthyristoren Phase control thyristors
CS13-06GO4 制造商:未知厂家 制造商全称:未知厂家 功能描述:Netzthyristoren Phase control thyristors
CS1308 制造商:Aten International 功能描述:Bulk
CS13-08GO4 制造商:未知厂家 制造商全称:未知厂家 功能描述:Netzthyristoren Phase control thyristors