参数资料
| 型号： | CS4360-KZZ |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 18/37页 |
| 文件大小： | 0K |
| 描述： | IC DAC STER 6CH 102DB 28TSSOP |
| 标准包装： | 50 |
| 位数： | 24 |
| 数据接口： | 串行 |
| 转换器数目： | 6 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 265mW |
| 工作温度： | -10°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 托盘 |
| 输出数目和类型： | 6 电压，单极 |
| 采样率（每秒）： | 192k |
| 产品目录页面： | 757 (CN2011-ZH PDF) |
| 其它名称： | 598-1642 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
CS4360
DS517F2
25
4.6.3
Discharge Time
To prevent an audio transient at the next power-on, the DC-blocking capacitors must fully discharge be-
fore turning on the power or exiting the power-down state. If full discharge does not occur, a transient will
occur when the audio outputs are initially clamped to GND. The time that the device must remain in the
power-down state is related to the value of the DC-blocking capacitance and the output load. For example,
with a 3.3 F capacitor, the minimum power-down time will be approximately 0.4 seconds.
4.7
Mute Control
The Mute Control pins go high during power-up initialization, reset, muting (see section 6.1.1 and 6.4.1),
or if the MCLK to LRCK ratio is incorrect. These pins are intended to be used as control for external mute
circuits to prevent the clicks and pops that can occur in any single-ended single supply system.
Use of the Mute Control function is not mandatory but recommended for designs requiring the absolute
minimum in extraneous clicks and pops. Also, use of the Mute Control function can enable the system
designer to achieve idle channel noise/signal-to-noise ratios which are only limited by the external mute
circuit. Please see the CDB4360 data sheet for a suggested mute circuit.
4.8
Grounding and Power Supply Arrangements
As with any high-resolution converter, the CS4360 requires careful attention to power supply and ground-
ing arrangements if its potential performance is to be realized. Figure 1 shows the recommended power
arrangements, with VA, VD, VLS and VLC connected to clean supplies. If the ground planes are split be-
tween digital ground and analog ground, the GND pins of the CS4360 should be connected to the analog
ground plane.
All signals, especially clocks, should be kept away from the FILT+ and VQ pins in order to avoid unwanted
coupling into the modulators. The CDB4360 evaluation board demonstrates the optimum layout and pow-
er supply arrangements.
4.8.1
Capacitor Placement
Decoupling capacitors should be placed as close to the DAC as possible, with the low-value ceramic ca-
pacitor being the closest. To further minimize impedance, these capacitors should be located on the same
layer as the DAC. If desired, all supply pins may be connected to the same supply, but a decoupling ca-
pacitor should still be placed on each supply pin and referenced to analog ground.
4.8.2
Power Supply Sections
Each power supply pin provides power to specific sections of the CS4360. The logic voltage level for each
section must adhere to the corresponding power supply voltage setting. For example: If VLC = 1.8 V; VLS
= 3.3 V; VD = VA = 5 V; then the logic level for all mode configuration inputs must equal 1.8 V.
4.9
Control Port Interface
The control port is used to load all the internal register settings (see section 6). The operation of the control
port may be completely asynchronous with the audio sample rate. However, to avoid potential interfer-
ence problems, the control port pins should remain static if no operation is required.
The control port operates in one of two modes: IC or SPI.
Notes: MCLK must be applied during all IC communication.
Pin #s
Description
Power Supply Reference
2, 3, 4, 5, 6, 7
Serial Audio Interface Inputs
VLS
10, 11, 12, 13, 15
Mode Configuration Inputs
VLC
Table 7. Power Supply Control Sections
相关PDF资料 |
PDF描述 |
|---|---|
| CS4361-CZZR | IC DAC STER 6CH 105DB 20-TSSOP |
| CS4362-KQZ | IC DAC 6CH 114DB 192KHZ 48LQFP |
| CS4362A-DQZ | IC DAC 6CH 114DB 192KHZ 48-LQFP |
| CS4364-CQZR | IC DAC 103DB 24BIT 6CH 48-LQFP |
| CS4382A-DQZ | IC DAC 8CH 114DB 192KHZ 48-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS4360-KZZR | 功能描述:数模转换器- DAC IC 102dB 24Bit 192kHz 6ch DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| CS4361 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:20-Pin, 24-Bit, 192 kHz, 6-Channel D/A Converter |
| CS4361_08 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:20-Pin, 24-Bit, 192 kHz, 6-Channel D/A Converter |
| CS4361-CZZ | 功能描述:音频数/模转换器 IC 6-Ch DAC 24-Bit 192kHz 105dB RoHS:否 制造商:Texas Instruments 转换器数量: 分辨率:16 bit 接口类型:I2S, UBS 转换速率: 信噪比:98 dB 工作电源电压:5 V DAC 输出端数量:2 工作温度范围:- 25 C to + 85 C 电源电流:23 mA 安装风格:SMD/SMT 封装 / 箱体:TQFP-32 封装:Reel |
| CS4361-CZZR | 功能描述:数模转换器- DAC IC 105dB 24-bit 192kHz 6ch DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。