- 您现在的位置：买卖IC网 > PDF目录13714 > CS51411EDR8G (ON Semiconductor)IC REG BUCK 1.5A SNGL 8SOIC PDF资料下载
参数资料
| 型号： | CS51411EDR8G |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 1.5A SNGL 8SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出数： | 1 |
| 输入电压： | 4.5 V ~ 40 V |
| PWM 型： | 混合物 |
| 频率 - 开关： | 260kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SOICN |
| 其它名称： | CS51411EDR8GOSDKR |
CS51411, CS51412, CS51413, CS51414
IO(MAX) + ILIM * O
independent of switching duty cycle. The maximum load
current, given by the following formula under continuous
conduction mode, is less than the Current Limit due to the
ripple current.
V (VIN * VO)
2(L)(VIN)(fs)
where:
f S = switching frequency,
I LIM = current limit threshold,
V O = output voltage,
V IN = input voltage,
L = inductor value.
When the regulator runs undercurrent limit, the
subharmonic oscillation may cause low frequency
oscillation, as shown in Figure 13. Similar to current mode
control, this oscillation occurs at the duty cycle greater than
50% and can be alleviated by using a larger inductor value.
The current limit threshold is reduced to Foldback Current
when the FB pin falls below Foldback Threshold. This
feature protects the IC and external components under the
power up or overload conditions.
where:
V F = diode forward voltage.
The anode of the diode can be connected to any DC voltage
other than the regulated output voltage. However, the
maximum voltage on the BOOST pin shall not exceed 40 V.
As shown in Figure 14, the BOOST pin current includes a
constant 7.0 mA predriver current and base current
proportional to switch conducting current. A detailed
discussion of this current is conducted in Thermal
Consideration section. A 0.1 m F capacitor is usually adequate
for maintaining the Boost pin voltage during the on time.
BIAS Pin (CS51412 and CS51414 Only)
The BIAS pin allows a secondary power supply to bias the
control circuitry of the IC. The BIAS pin voltage should be
between 3.3 V and 6.0 V. If the BIAS pin voltage falls below
that range, use a diode to prevent current drain from the
BIAS pin. Powering the IC with a voltage lower than the
regulator ’s input voltage reduces the IC power dissipation
and improves energy transfer efficiency.
30
25
20
15
10
5
0
0
0.5 1.0
1.5
SWITCHING CURRENT (A)
Figure 14. The Boost Pin Current Includes 7.0 mA
Predriver Current and Base Current when the Switch
Figure 13. The Regulator in Current Limit
BOOST Pin
The BOOST pin provides base driving current for the
power switch. A voltage higher than V IN provides required
headroom to turn on the power switch. This in turn reduces
IC power dissipation and improves overall system
efficiency. The BOOST pin can be connected to an external
boost ? strapping circuit which typically uses a 0.1 m F capacitor
and a 1N914 or 1N4148 diode, as shown in Figure 1. When the
power switch is turned on, the voltage on the BOOST pin is
equal to
VBOOST + VIN ) VO * VF
is Turned On. The Beta Decline of the Power Switch
Further Increases the Base Current at High
Switching Current
Shutdown
The internal power switch will not turn on until the V IN
pin rises above the Startup Voltage. This ensures no
switching until adequate supply voltage is provided to the
IC. The IC transitions to sleep mode when the SHDNB pin
is pulled low. In sleep mode, the internal power switch
transistor remains off and supply current is reduced to the
Shutdown Quiescent Current value (20 m A typical). This pin
has an internal pull-up current source, so defaults to high
(enabled) state when not connected.
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| SCB73C-470 | INDUCTOR SMD 47UH 0.60A 1KHZ |
| MAX6726AKAMSD6+T | IC SUPERVISOR MPU SOT23-8 |
| SCB73C-3R3 | INDUCTOR SMD 3.3UH 2.26A 1KHZ |
| SCB73C-390 | INDUCTOR SMD 39UH 0.67A 1KHZ |
| MAX6726AKAMSD5+T | IC SUPERVISOR MPU SOT23-8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS51411EMNR2G | 功能描述:直流/直流开关调节器 1.5A 260kHz BUCK REG LOW VOLTAGE RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| CS51411EVB | 功能描述:电源管理IC开发工具 ANA CS51411/3 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| CS51411GD8 | 功能描述:直流/直流开关调节器 1.5A Low Voltage RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| CS51411GD8G | 功能描述:直流/直流开关调节器 1.5A Low Voltage Buck RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| CS51411GDR8 | 功能描述:直流/直流开关调节器 1.5A Low Voltage RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。