- 您现在的位置：买卖IC网 > PDF目录11818 > CS82C50A-5Z96 (Intersil)IC ASYNC COMM ELEMNT UART 44PLCC PDF资料下载
参数资料
| 型号： | CS82C50A-5Z96 |
| 厂商： | Intersil |
| 文件页数： | 4/25页 |
| 文件大小： | 0K |
| 描述： | IC ASYNC COMM ELEMNT UART 44PLCC |
| 标准包装： | 500 |
| 特点： | 单芯片 UART/BRG |
| 通道数： | 1，UART |
| 规程： | RS232C |
| 电源电压： | 4.5 V ~ 5.5 V |
| 带并行端口： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 带卷 (TR) |
12
FN2958.5
August 24, 2006
data in the RBR before complete reception of the next
character result in the loss of the data in the Receiver
Register. The OE flag in the LSR register indicates the
overrun condition.
TRANSMITTER HOLDING REGISTER (THR)
The Transmitter Holding Register (THR) holds parallel data
from the data bus (D0-D7) until the Transmitter Shift Register
is empty and ready to accept a new character for
transmission. The transmitter and receiver word length and
number of stop bits are the same. If the character is less
than eight bits, unused bits at the microprocessor data bus
are ignored by the transmitter.
Data Bit 0 (THR(0)) is the first serial data bit transmitted. The
THRE flag (LSR(5)) reflect the status of the THR. The TEMT
flag (LSR(6)) indicates if both the THR and TSR are empty.
SCRATCHPAD REGISTER (SCR)
This 8-bit Read/Write register has no effect on the 82C50A.
It is intended as a scratchpad register to be used by the
programmer to hold data temporarily.
Interrupt Structure
INTERRUPT IDENTIFICATION REGISTER (IIR)
The 82C50A has interrupt capability for interfacing to current
microprocessors. In order to minimize software overhead
during data character transfers, the 82C50A prioritizes
interrupts into four levels. The four levels of interrupt
conditions are as follows:
1. Receiver Line Status (Priority 1)
2. Received Data Ready (Priority 2)
3. Transmitter Holding Register Empty (Priority 3)
4. Modem Status (Priority 4).
Information indicating that a prioritized interrupt is pending
and the type of interrupt is stored in the Interrupt
Identification Register (IIR). When addressed during chip
select time, the lIR indicates the highest priority interrupt
pending. No other interrupts are acknowledged until the
interrupt is serviced by the CPU. The contents of the lIR are
indicated in Table 2 and are described below.
IIR(0): IIR(0) can be used in either a hardwired prioritized or
polled environment to indicate whether an interrupt is
pending. When IIR(0) is low, an interrupt is pending, and the
lIR contents may be used as a pointer to the appropriate
interrupt service routine. When lIR(0) is high, no interrupt is
pending.
IlR(1) and IIR(2): llR(1) and IlR(2) are used to identify the
highest priority interrupt pending as indicated in Table 2.
lIR(3) - IIR(7): These five bits of the lIR are logic 0.
RBR Bits 0 thru 7
RBR (0)
Data Bit 0
RBR (1)
Data Bit 1
RBR (2)
Data Bit 2
RBR (3)
Data Bit 3
RBR (4)
Data Bit 4
RBR (5)
Data Bit 5
RBR (6)
Data Bit 6
RBR (7)
Data Bit 7
THR Bits 0 thru 7
THR (0)
Data Bit 0
THR (1)
Data Bit 1
THR (2)
Data Bit 2
THR (3)
Data Bit 3
THR (4)
Data Bit 4
THR (5)
Data Bit 5
THR (6)
Data Bit 6
THR (7)
Data Bit 7
SCR Bits 0 thru 7
SCR (0)
Data Bit 0
SCR (1)
Data Bit 1
SCR (2)
Data Bit 2
SCR (3)
Data Bit 3
SOR (4)
Data Bit 4
SCR (5)
Data Bit 5
SOR (6)
Data Bit 6
SCR (7)
Data Bit 7
TABLE 2. INTERRUPT IDENTIFICATION REGISTER
INTERRUPT IDENTIFICATION
INTERRUPT SET AND RESET FUNCTIONS
BIT 2
BIT 1
BIT 0
PRIORITY
LEVEL
INTERRUPT FLAG
INTERRUPT SOURCE
INTERRUPT
RESET CONTROL
X
1
None
1
0
First
Receiver Line Status
OE, PE, FE, or BI
LSR Read
1
0
Second
Received Data Available
Receiver Data Available
RBR Read
0
1
0
Third
THRE
IIR Read if THRE is the
Interrupt Source or THR Write
0
Fourth
Modem Status
CTS, DSR, RI, DCD
MSR Read
NOTE:
X = Not Defined, May Be 0 or 1
82C50A
相关PDF资料 |
PDF描述 |
|---|---|
| CS82C50A-5Z | IC COMMUNICATION ELEMENT 44-PLCC |
| CP82C52Z | IC UART/BRG 5V 16MHZ 28-PDIP |
| ATUC128D4-AUR | IC MCU 32BIT 128KB FLASH 48TQFP |
| VI-B72-IW-F2 | CONVERTER MOD DC/DC 15V 100W |
| V24C12H150B2 | CONVERTER MOD DC/DC 12V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS82C52 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS82C5296 | 功能描述:IC UART/BRG 5V 16MHZ 28-PLCC RoHS:否 类别:集成电路 (IC) >> 接口 - UART（通用异步接收器/发送器） 系列:- 标准包装:250 系列:- 特点:* 通道数:2，DUART FIFO's:16 字节 规程:RS232，RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:托盘 其它名称:XR16L2551IM-F-ND |
| CS82C52Z | 功能描述:UART 接口集成电路 A/ANNEAL PERIPH UART /BRG 5V 16MHZ 28PLCC RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| CS82C52Z96 | 功能描述:UART 接口集成电路 A/ANNEAL PERIPH UART /BRG 5V 16MHZ 28PLCC RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| CS82C54 | 功能描述:计时器和支持产品 PERIPH PRG-CNTR 5V 8MHZ 28PLCC COM RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。