- 您现在的位置：买卖IC网 > Datasheet目录402 > CSM56F801SLK (Freescale Semiconductor)KIT LEARNING DSP 16BIT CSM56F801 Datasheet资料下载
参数资料
| 型号： | CSM56F801SLK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 3/13页 |
| 文件大小： | 0K |
| 描述： | KIT LEARNING DSP 16BIT CSM56F801 |
| 标准包装： | 1 |
D O C - 0 3 3 4 - 0 1 0 ,
R E V
D
D E C E M B E R
2 ,
2 0 0 5
REVISION
Date
December 2, 2005
Rev
C
Comments
Updated format and revision
Freescale Semiconductor, Inc.
CAUTIONARY NOTES
1) Electrostatic Discharge (ESD) prevention measures should be used when handling this
product. ESD damage is not a warranty repair item.
2) Axiom Manufacturing does not assume any liability arising out of the application or use of
any product or circuit described herein; neither does it convey any license under patent
rights or the rights of others.
3) EMC Information on the CSM-56F801 module:
a) This product as shipped from the factory with associated power supplies and cables, has
been verified to meet with requirements of CE and the FCC as a CLASS B product.
b) This product is designed and intended for use as a development platform for hardware
or software in an educational or professional laboratory.
c) In a domestic environment, this product may cause radio interference in which case the
user may be required to take adequate prevention measures.
d) Attaching additional wiring to this product or modifying the products operation from the
factory default as shipped may effect its performance and cause interference with nearby
electronic equipment. If such interference is detected, suitable mitigating measures
should be taken.
TERMINOLOGY
This development module uses option selection jumpers and cut-traces to setup default
configuration. Terminology for application of the option jumpers is as follows:
Jumper – a plastic shunt that connects 2 terminals electrically
Jumper on, in, or installed - jumper is installed such that 2 pins are connected together
Jumper off, out, or idle - jumper is installed on 1 pin only. It is recommended that
jumpers be idled by installing on 1 pin so they will not be lost.
Cut-Trace – a circuit trace connection between component pads. The circuit trace may
be cut using a razor knife to break the default connection. To reconnect the circuit,
simply install a suitably sized 0-ohm resistor or attach a wire across the pads.
3
相关PDF资料 |
PDF描述 |
|---|---|
| CT 0.1-P | TRANSDUCER CURRENT 0.2A 15V |
| CT4-MLXF | LINKING CABLE 4WAY-8WAY FEMALE |
| CTSR 0.3-TP | TRANSDUCER CURRENT 0.3A 15V |
| CTSR 0.6-P | TRANSDUCER CURRENT 0.6A |
| CTSR 0.6-TP | TRANSDUCER CURRENT 0.6A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CSM-57031A9 | 制造商:CHINASEMI 制造商全称:China Semiconductor Corporation 功能描述:0.7Inch Dot-Matrix Display |
| CSM57031D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| CSM57031E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| CSM-57031E | 制造商:CHINASEMI 制造商全称:China Semiconductor Corporation 功能描述:0.7Inch Dot-Matrix Display |
| CSM57031G | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
发布紧急采购，3分钟左右您将得到回复。