参数资料
| 型号： | CU4032K60G2 |
| 厂商： | EPCOS Inc |
| 文件页数： | 28/35页 |
| 文件大小： | 0K |
| 描述： | VARISTOR STD 60VRMS 4032 SMD |
| 产品目录绘图： | CU4032K Series_Max V Allowance 11~175 Side1 CU4032K Series_Max V Allowance 11~175 Side2 |
| 标准包装： | 2,000 |
| 系列： | CU |
| 变阻器电压： | 100V |
| 电流 - 浪涌： | 1.2kA |
| 电路数： | 1 |
| 最大交流电压： | 60VAC |
| 最大直流电压： | 85VDC |
| 能量： | 4.8J |
| 封装/外壳： | 4032（1080 公制） |
| 其它名称： | B72660M600K72 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页
SMD disk varistors (CU varistors)
Standard series
7.5
Adhesive application
Thin or insufficient adhesive causes chips to loosen or become disconnected during curing.
Low viscosity of the adhesive causes chips to slip after mounting. It is advised to consult the
manufacturer of the adhesive on proper usage and amounts of adhesive to use.
7.6
Selection of flux
Used flux should have less than or equal to 0.1 wt % of halogenated content, since flux residue
after soldering could lead to corrosion of the termination and/or increased leakage current on the
surface of the component. Strong acidic flux must not be used. The amount of flux applied should
be carefully controlled, since an excess may generate flux gas, which in turn is detrimental to sol-
derability.
7.7
Storage of CTVSs
Solderability is guaranteed for one year from date of delivery for multilayer varistors, CeraDiodes
and ESD/EMI filters (half a year for chips with AgPd and AgPt terminations) and two years for
SHCV and CU components, provided that components are stored in their original packages.
Storage temperature:
Relative humidity:
25 ° C to +45 ° C
≤ 75% annual average, ≤ 95% on 30 days a year
The solderability of the external electrodes may deteriorate if SMDs and leaded components are
stored where they are exposed to high humidity, dust or harmful gas (hydrogen chloride, sulfurous
acid gas or hydrogen sulfide).
Do not store SMDs and leaded components where they are exposed to heat or direct sunlight.
Otherwise the packing material may be deformed or SMDs/ leaded components may stick togeth-
er, causing problems during mounting.
After opening the factory seals, such as polyvinyl-sealed packages, it is recommended to use the
SMDs or leaded components as soon as possible.
7.8
Placement of components on circuit board
Especially in the case of dual-wave soldering, it is of advantage to place the components on the
board before soldering in that way that their two terminals do not enter the solder bath at different
times.
Ideally, both terminals should be wetted simultaneously.
7.9
Soldering cautions
An excessively long soldering time or high soldering temperature results in leaching of the outer
electrodes, causing poor adhesion and a change of electrical properties of the varistor due to
the loss of contact between electrodes and termination.
Wave soldering must not be applied for MLVs designated for reflow soldering only.
Keep the recommended down-cooling rate.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 28 of 35
相关PDF资料 |
PDF描述 |
|---|---|
| CU4032K50G2 | VARISTOR STD 50VRMS 4032 SMD |
| BZA820A,115 | TVS ZENER QUAD 20V SOT353 |
| CU4032K40G2 | VARISTOR STD 40VRMS 4032 SMD |
| CU4032K35G2 | VARISTOR STD 35VRMS 4032 SMD |
| CU4032K30G2 | VARISTOR STD 30VRMS 4032 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CU4032K75G | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| CU4032K75G2 | 功能描述:VARISTOR STD 75VRMS 4032 SMD RoHS:是 类别:过电压，电流，温度装置 >> TVS - 变阻器，MOV 系列:CU 标准包装:300 系列:RA 变阻器电压:68V 电流 - 浪涌:1kA 电路数:1 最大交流电压:40VAC 最大直流电压:56VDC 能量:13J 封装/外壳:径向，盒式 |
| CU4032K95G | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| CU4032K95G2 | 功能描述:VARISTOR STD 95VRMS 4032 SMD RoHS:是 类别:过电压，电流，温度装置 >> TVS - 变阻器，MOV 系列:CU 标准包装:300 系列:RA 变阻器电压:68V 电流 - 浪涌:1kA 电路数:1 最大交流电压:40VAC 最大直流电压:56VDC 能量:13J 封装/外壳:径向，盒式 |
| CU4032S60AG2 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:SMD Varistors |
发布紧急采购，3分钟左右您将得到回复。