- 您现在的位置：买卖IC网 > PDF目录19192 > CUB7TCS0 (Red Lion Controls)TIMER LCD PROGRAM 8-DIGIT LV REF PDF资料下载
参数资料
| 型号： | CUB7TCS0 |
| 厂商： | Red Lion Controls |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | TIMER LCD PROGRAM 8-DIGIT LV REF |
| 标准包装： | 1 |
| 系列： | CUB7 |
| 工作模式： | 累积 |
| 输出类型： | 无 |
| 电源电压： | 不需要（包括电池） |
| 端接类型： | 导线引线 |
| 显示器类型： | LCD 无背光 |
| 产品目录页面： | 2853 (CN2011-ZH PDF) |
| 其它名称： | RLC132 |
USING THE OPTIONAL TERMINAL BLOCK
1. Remove the rear cover. Refer to Figure 1. A small slotted screwdriver is
required to release the side latches. Insert the screwdriver tip between the
rear cover and the side of the unit. Leverage the screwdriver away from the
case to unlatch the side latch and slightly lift the rear cover. Pinch the
corners to hold the rear cover in place. Remove the screwdriver and repeat
the same procedure on the other side of the rear cover. When both side
latches are released, slide the rear cover from the unit and the wires.
2. For safety concerns, the wires should be cut off completely flush with the PC
board to prevent a short.
3. Break out the break away tab(s) as required. Remove the left tab only for 3
position terminal block or both tabs for 4 and 5 position terminal blocks.
4. Reinstall the rear cover into CUB7 unit.
5. Mount the CUB7 into the panel (refer to 1.0 Installing The Meter)
6. Push the keyed terminal block onto the exposed PC board. The left most
terminal, next to the DIP switch(s) is terminal #1.
Note: Wire sizes 16-24 AWG may be used with 0.25" length exposed. The
screwless type terminal block requires a small slotted screwdriver engaged in
the upper slot to open the wire clamp in the lower larger slot. Removing the
screwdriver will lock the wire clamp unto the wire.
Side
Latches
Figure 1
Rear Cover
Mounting Clip
DIP Switch(s)
Cut Wires Internally
(If using Optional
Terminal Block)
Wires must be cut off completely
flush with PC board.
Side Latches
Break-out Tab or Tabs
(If using Optional
Terminal Block)
Open & Lock
Wire Clamp
Optional
Terminal Block
Terminal #1
Current Sinking Output
Current Sourcing Output
Logic Output
ON
*
1 2 3
1
2
3
4
+
?
Optional
Backlight
Power
ON
*
1 2 3
+V
1
2
3
4
+
?
Optional
Backlight
Power
ON
*
1 2 3
1
2
3
4
+
?
Optional
Backlight
Power
Switch/Contact Sinking Output
Switch/Contact Sourcing Output
High Voltage
ON
*
1 2 3
1
2
3
4
+
?
Optional
Backlight
Power
ON
*
1 2 3
+V
1
2
3
4
+
?
Optional
Backlight
Power
ON
*
3
50-250
VDC/VAC
1
2
3
4
5
+
?
Optional
Backlight
Power
Switch position is application dependent.
6
Shaded area for high voltage applications.
相关PDF资料 |
PDF描述 |
|---|---|
| HR31-TC-01 | TOOL MANUAL CRIMP FOR HR31 |
| 210-12ESFD | SWITCH EXTENDED ACTUATOR 12 SEC |
| 210-12MSFD | SWITCH RAISED ACTUATOR 12 SEC |
| 210-12LPSFD | SWITCH SPST 12 SEC LOW PROFILE |
| NDF02N60ZG | MOSFET N-CH 600V 4.8OHM TO220FP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CUB7TCS1 | 功能描述:TIMER LCD PROGRAM 8-DIGIT LV REF RoHS:是 类别:工业控制，仪表 >> 定时器 系列:* 标准包装:10 系列:- 计时范围:- 工作模式:累积 输出类型:- 电源电压:4.5 V ~ 10 V 端接类型:PCB 引脚 显示器类型:无显示器 其它名称:2001PC-001 5VDCQ1273012Q1443992 |
| CUB7TVG0 | 功能描述:TIMER LCD PROGRAM 8-DIGIT HV GRN RoHS:是 类别:工业控制，仪表 >> 定时器 系列:CUB7 标准包装:10 系列:- 计时范围:- 工作模式:累积 输出类型:- 电源电压:4.5 V ~ 10 V 端接类型:PCB 引脚 显示器类型:无显示器 其它名称:2001PC-001 5VDCQ1273012Q1443992 |
| CUB7TVR0 | 功能描述:TIMER LCD PROGRAM 8-DIGIT HV RED RoHS:是 类别:工业控制，仪表 >> 定时器 系列:CUB7 标准包装:10 系列:- 计时范围:- 工作模式:累积 输出类型:- 电源电压:4.5 V ~ 10 V 端接类型:PCB 引脚 显示器类型:无显示器 其它名称:2001PC-001 5VDCQ1273012Q1443992 |
| CUB7TVS0 | 功能描述:TIMER LCD PROGRAM 8-DIGIT HV REF RoHS:是 类别:工业控制，仪表 >> 定时器 系列:CUB7 标准包装:10 系列:- 计时范围:- 工作模式:累积 输出类型:- 电源电压:4.5 V ~ 10 V 端接类型:PCB 引脚 显示器类型:无显示器 其它名称:2001PC-001 5VDCQ1273012Q1443992 |
| CUB7TVSO | 制造商:Red Lion Controls 功能描述:ELECTRONIC TIMER VOLTAGE LCD 制造商:Red Lion Controls 功能描述:ELECTRONIC TIMER, VOLTAGE, LCD |
发布紧急采购，3分钟左右您将得到回复。