- 您现在的位置：买卖IC网 > Datasheet目录620 > CUB7W020 (Red Lion Controls)COUNTER 8-DIGIT RED BKLT VOLT-IN Datasheet资料下载
参数资料
| 型号： | CUB7W020 |
| 厂商： | Red Lion Controls |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | COUNTER 8-DIGIT RED BKLT VOLT-IN |
| 标准包装： | 1 |
| 系列： | CUB7 |
| 计数速率： | 30Hz |
| 数字/字母数： | 8 |
| 输入类型： | 电压 |
| 电源电压： | 不需要（包括电池） |
| 显示器类型： | LCD 背光 |
| 其它名称： | RLCW72 |
L. S. INPUT, 30 CPS MAX.
The CUB7W accepts most machine control voltage signals. The input accepts
AC (50/60 Hz) or DC control voltages from 10 to 300 V at count speeds up to
30 cps. The unit counts on the positive going edge of the input signal.
WARNING : Any lead may be at hazardous live input potential.
External wiring and devices connected to the unit must be rated
the same as applied signal input voltage and be properly isolated
from Class 2 or SELV circuitry.
INSTALLATION ENVIRONMENT
The unit should be installed in a location that does not exceed the maximum
operating temperature and provides good air circulation. Placing the unit near
devices that generate excessive heat should be avoided.
The bezel should be cleaned only with a soft cloth and neutral soap product.
Do NOT use solvents.
Continuous exposure to direct sunlight may accelerate the aging process of
the bezel.
Do not use tools of any kind (screwdrivers, pens, pencils, etc.) to operate
the keypad of the unit.
Installation
The CUB7 series of products meets NEMA 4X/IP65 requirements for
indoor use, when properly installed. The units are intended to be mounted into
an enclosed panel. The viewing window and reset button are factory sealed for
a washdown environment. A sponge rubber gasket and mounting clip are
provided for installing the unit in the panel cut-out.
The following procedure assures proper installation:
1. Cut panel opening to specified dimensions. Remove burrs and clean around
panel opening.
2. Carefully remove and discard the center section of the gasket. Slide the
panel gasket over the rear of the unit to the back of the bezel. Insert the
mounting screws onto both sides of mounting clip. Tip of screw should
NOT project from hole in mounting clip.
3. Install CUB7 unit through the panel cut-out until front bezel flange contacts
the panel.
4. Slide the mounting clip over the rear of the unit until the clip is against the
back of the panel. The mounting clip has latching features which engage
into mating features on the CUB7 housing.
BATTERY INSTALLATION
1. Remove all power to the unit before removing battery cover.
2. To remove battery cover, push upward in the direction of the arrow on rear
cover (See drawing at right), until the cover unlatches. Pull cover straight
out from unit to fully remove.
3. Remove old battery* and replace with an RLC battery (BNL10000).
Observe proper polarity when replacing battery as shown in drawing.
4. Replace cover. The battery cover is keyed so that it cannot be placed upside
down. The arrow on the rear of the cover should point toward the top of the
CUB7 series when properly installed
* - Dispose of properly.
WARNING : Lithium battery may explode if incinerated.
3
Note: It is necessary to hold the unit in place when sliding mounting clip
into position.
5. Alternately tighten each screw to ensure uniform gasket pressure.
Visually inspect the front panel gasket. The gasket should be compressed to
about 75 to 80% of its original thickness. If not, gradually turn mounting
screws to further compress gasket.
6. If gasket is not adequately compressed and the mounting screws can no
longer be turned, loosen mounting screws, and check that mounting clip is
latched as close as possible to the panel.
7. Repeat from step #5 for tightening mounting screws.
相关PDF资料 |
PDF描述 |
|---|---|
| D-659-0001 | TOOL REMOVAL MTC CONN WAFER |
| D7-1 | DIE, .041 HOLE DIA |
| DH2X61-18A | DIODE FST REC 1800V2X60A SOT227B |
| DHG100X1200NA | DIODE ARRAY 1200V 50A SOT227B |
| DHG50X1200NA | DIODE ARRAY 1200V 25A SOT227B |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CUB8A-1 | 制造商:IMO Precision Controls Ltd 功能描述:INVERTER 1 PHASE 1.5KW 制造商:IMO Precision Controls Ltd 功能描述:AC MOTOR DRIVER; Supply Voltage Min:200VAC; Supply Voltage Max:240VAC; No. of Phases:Single; Power Rating:1.5kW; Output Voltage Max:230V; External Depth:151mm; Frequency Range:0.1 to 400Hz; Input Current:16.4A; Output Current:8A ;RoHS Compliant: Yes |
| CUB8A-1 | 制造商:IMO Precision Controls Ltd 功能描述:INDICATOR M/BLOCK LED 24AC RED |
| CUB9A-4 | 制造商:IMO Precision Controls Ltd 功能描述:INVERTER 3 PHASE 4KW 制造商:IMO Precision Controls Ltd 功能描述:AC MOTOR DRIVER; Supply Voltage Min:380VAC; Supply Voltage Max:480VAC; No. of Phases:Three; Power Rating:4kW; Output Voltage Max:415V; External Depth:141mm; Frequency Range:0.1 to 400Hz; Input Current:13A; Output Current:9A ;RoHS Compliant: Yes |
| CUB9A-4 | 制造商:IMO Precision Controls Ltd 功能描述:INVERTER 3 PHASE 0.75KW |
| CUB9A-4 | 制造商:IMO Precision Controls Ltd 功能描述:INVERTER 3 PHASE 4.0KW ((NS)) |
发布紧急采购，3分钟左右您将得到回复。