- 您现在的位置：买卖IC网 > PDF目录16692 > D-300-01 (TE Connectivity)HEAT SHRINK CAP FOR SPLICE PDF资料下载
参数资料
| 型号： | D-300-01 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/7页 |
| 文件大小： | 0K |
| 描述： | HEAT SHRINK CAP FOR SPLICE |
| 标准包装： | 1,000 |
| 类型： | 端盖 |
| 收缩比率： | 2 至 1 |
| 长度： | 0.083'（25.40mm，1.00"） |
| 内径 - 提供： | 0.175"（4.4mm） |
| 内径 - 恢复： | 0.080"（2.0mm） |
| 已恢复的墙壁厚度： | 0.030"（0.76mm） |
| 材质： | 聚烯烃 |
| 特点： | 阻燃 |
| 颜色： | 黑 |
| 其它名称： | 610004-000 |
SPECIFICATION CONTROL DRAWING
4.2.1
4.2.1
4.2.1
4.2.1
Heat Aging: Fifteen assemblies shall be conditioned for 1000 hours at 150 ± 3 ° C (302 ± 5 ° F) in a
mechanical-convection oven with an air velocity of 100 to 200 feet per minute past the specimens. After
conditioning, the specimen shall be cooled to 25 ± 5 ° C (77 ± 9 ° F) within one hour and tested for insulation
resistance (4.4.3) and dielectric withstanding voltage (4.4.4).
Altitude Immersion: Fifteen assemblies shall be immersed in a water bath containing 5% by weight of
NaCl and placed in a chamber. Wire ends, opposite the cap, shall be within the chamber, but not
submerged. The exposed wire ends shall not be sealed. The chamber pressure shall be reduced to
approximately 1 inch of mercury and maintained for 30 minutes. The chamber pressure shall then be
returned to atmospheric pressure. The insulation assistance shall be measured in accordance with 4.4.3.
This shall constitute one cycle. Two additional environment cycles shall be run. At the end of the third
cycle, the insulation resistance (4.4.3) shall be re-measured, and the dielectric withstanding voltage test
(4.4.4) shall be performed.
Corrosive effect: Two caps, as supplied, shall be placed in the bottoms of two clean ? x 12 inches test
tubes (one cap per tube). A third tube shall be used for control. A copper-glass mirror, about 1 x ? inches
shall be suspended from 6 to 7 inches above the bottom of each tube by a fine copper wire attached to a
cork wrapped in aluminum foil. The corks shall tightly seal the test tubes. The lower 2 inches of each tube
then shall be placed in an oven or oil bath at 175 ± 3 ° C for 16 hours. After cooling, the mirrors shall be
examined in a good light against a white background. Evidence of corrosion shall be areas of transparency
larger than pinholes in a mirror. Discoloration of the copper film or reduction of its thickness shall not be
considered corrosion. The mirrors shall be vacuum- deposited copper with thickness equal to 10 ± 5%
transmission of normal incident light of 5000 angstroms. They shall be stored in a vacuum and shall be
used for test only if no oxide film is present and the copper is not visibly damaged.
Flammability: Specimens shall be mounted horizontally in a draft-free chamber. A standard 1/8” Bunsen
burner shall be adjusted to produce a blue flame approximately 1” high. This flame shall be applied at a
distance of 1” to the closed end of the test specimen for 10 seconds. The flame shall then be removed and
the specimen shall remain undisturbed until burning ceases. Failure of more than one specimen to
extinguish itself with 30 seconds shall be cause for rejection.
TABLE 1
REQUIREMENTS FOR MOLDED COMPONENT
Property
Tensile Strength
Ultimate Elongation
Stiffness
Unit
psi
percent
psi
Requirement
1500 minimum
250 minimum
10,000 minimum
Method of Test
Section 4.3.1
(ASTM D 412)
ASTM D 747
25,000 maximum
Specific Gravity
1.40 maximum
ASTM D 792
307 Constitution Drive Menlo Park, CA 94025, USA
Wire and
Harnessing
Products
TITLE :
CAP, SPLICE ENCAPSULATION
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS.
INCHES DIMENSIONS ARE BETWEEN BRACKETS.
DOCUMENT NO.:
D-300-01/-03
TOLERANCES:
0.00 N/A
0.0 N/A
0 N/A
ANGLES: N/A
ROUGHNESS IN
MICRON
Tyco Electronics reserves the right to amend
this drawing at any time. Users should
evaluate the suitability of the product for
their application.
DCR NUMBER:
D010043
REPLACES:
N/A
DRAWN BY:
M. FORONDA
DATE:
15-Feb.-01
PROD. REV.
SEE TABLE
DOC ISSUE:
1
SCALE:
None
SIZE:
A
SHEET:
4 of 7
If this document is printed it becomes uncontrolled. Check for the latest revision.
相关PDF资料 |
PDF描述 |
|---|---|
| H3BKH-1006M | IDC CABLE - HSR10H/AE10M/HPK10H |
| V72C28E150BL | CONVERTER MOD DC/DC 28V 150W |
| GCB15DHHD | CONN EDGECARD 30POS .050 DIP SLD |
| PI2007-EVAL1 | EVAL BRD FOR PI2007 48V/6A |
| A3BBB-1406G | IDC CABLE- ASR14B/AE14G/ASR14B |
相关代理商/技术参数 |
参数描述 |
|---|---|
| D300015C | 制造商:Mersen 功能描述:Protistor DIN80 size 31 FF fuse,500A |
| D-300-01CS1108 | 制造商:TE Connectivity 功能描述:D-300-01CS1108 |
| D-300-01CS4012 | 制造商:TE Connectivity 功能描述:CZ6606-000 |
| D-300-01CS834 | 功能描述:焊料和屏蔽管 RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03 |
| D-300-02 | 功能描述:焊料和屏蔽管 RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03 |
发布紧急采购，3分钟左右您将得到回复。