- 您现在的位置：买卖IC网 > Datasheet目录973 > D-300-02 (TE Connectivity)HEAT SHRINK CAP FOR SPLICE Datasheet资料下载
参数资料
| 型号： | D-300-02 |
| 厂商： | TE Connectivity |
| 文件页数： | 7/7页 |
| 文件大小： | 0K |
| 描述： | HEAT SHRINK CAP FOR SPLICE |
| 标准包装： | 1,000 |
| 类型： | 端盖 |
| 收缩比率： | 2 至 1 |
| 长度： | 0.092'（27.94mm，1.10"） |
| 内径 - 提供： | 0.250"（6.4mm） |
| 内径 - 恢复： | 0.120"（3.0mm） |
| 已恢复的墙壁厚度： | 0.040"（1.02mm） |
| 材质： | 聚烯烃 |
| 特点： | 阻燃 |
| 颜色： | 黑 |
| 其它名称： | 610015-000 |
SPECIFICATION CONTROL DRAWING
Thermofit Assembly Procedure
1.
2.
3.
4.
5.
Strip the wires and install crimp type connector or solder wires together. Connector should be installed so that
1/6 ± 1/32 of conductor is exposed between the connector and the wire insulation, as shown in Figure 1.
Choose the proper size cap from the chart below. Place splice into cap so that the connector bottoms on the
rounded end of the cap.
Heat the assembly, using a Thermogun, Model 500A, or equivalent, equipped with a TG-12 or TG-13A
reflector.
The average length of time required for proper heating is given in the chart. However, since the heat sink effect
of various wire bundles may vary considerably, several trial specimens should be crossed-sectioned as shown in
Figure 2 before proceeding with production installations. If the area between the wires is not completely filled,
a longer heating cycle should be established.
With wire bundles of more than three wires, it is helpful to slightly deform the cap by pinching in the area
above the connection at the end of the heating cycle and then returning the cap to the heat for an additional
period to allow the cap to return to its cylindrical shape.
Chart 1
Part
Name
D-300-01
D-300-02
D-300-03
Figure 1
Splicer Diameter
Minimum Maximum
2.03 (0.080) 4.91 (0.165)
3.04 (0.120) 6.35 (0.250)
4.57 (0.180) 8.89 (0.350)
Figure 2
Time
(sec.)
30
45
60
Bundle Diameter
Maximum
.115
.200
.300
307 Constitution Drive Menlo Park, CA 94025, USA
Wire and
Harnessing
Products
TITLE :
CAP, SPLICE ENCAPSULATION
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS.
INCHES DIMENSIONS ARE BETWEEN BRACKETS.
DOCUMENT NO.:
D-300-01/-03
TOLERANCES:
0.00 N/A
0.0 N/A
0 N/A
ANGLES: N/A
ROUGHNESS IN
MICRON
Tyco Electronics reserves the right to amend
this drawing at any time. Users should
evaluate the suitability of the product for
their application.
DCR NUMBER:
D010043
REPLACES:
N/A
DRAWN BY:
M. FORONDA
DATE:
15-Feb.-01
PROD. REV.
SEE TABLE
DOC ISSUE:
1
SCALE:
None
SIZE:
A
SHEET:
7 of 7
If this document is printed it becomes uncontrolled. Check for the latest revision.
相关PDF资料 |
PDF描述 |
|---|---|
| D-436-0098 | SOLDER SLEEVE .025" DIA IMM RES |
| D-500-L455-3-613-120 | MICROSOUPLER 3 STUB DBL SHIELD |
| D-659-0026 | HEAT SHRINK SLD SLEEVE SHIELD |
| D06D80 | RELAY SSR 80A 0-60V DC OUTPUT |
| D15532-000 | HX-SCE-1K-12.7-50-4 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| D-300-02CS1108 | 制造商:TE Connectivity 功能描述:D-300-02CS1108 |
| D-300-02CS834 | 功能描述:焊料和屏蔽管 RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03 |
| D-300-03 | 功能描述:焊料和屏蔽管 Splice Encap. Cap 12AWG 3 Wires RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03 |
| D-300-03CS1108 | 制造商:TE Connectivity 功能描述:D-300-03CS1108 制造商:TE Connectivity 功能描述:Cap, Splice Encapsulation |
| D-300-03CS834 | 功能描述:焊料和屏蔽管 RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03 |
发布紧急采购，3分钟左右您将得到回复。