参数资料
| 型号： | D-436-88 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/2页 |
| 文件大小： | 0K |
| 描述： | CONN SPLICE BUTT 24-28AWG RED |
| 标准包装： | 500 |
| 端子类型： | 对接接头，直插式，单独开口 |
| 导线入口数目： | 2 |
| 端子： | 压接 |
| 线规： | 24-28 AWG |
| 绝缘体： | 完全绝缘 |
| 特点： | 热收缩 |
| 颜色： | 蓝，红条纹 |
| 包装： | 散装 |
| 其它名称： | 2-1195133-5 650132-000 |
SPECIFICATION CONTROL DRAWING
MIL Spec equivalent s ize and wire accomodation :
Part
Name
MIL Spec
Equivalent Size
Wire Size
Range (AWG)
Wgt. Lbs/Mpc
max
D-436-88 M81824/1-1
D-436-89 M81824/1-2
D-436-90 M81824/1-3
26 - 20
20 - 16
16 - 12
1.02
1.61
2.72
APPLICATION
1. These parts are designed to provide immersion resistant in-line splices of 2 or 3 to 2 or 3 wires falling within
the size range listed on sheet 1, having nickel-plated conductors and insulations rated for at least 135 ? C.
2. Parts are available only as an assembly of one of each Item #1 and Item #2.
3. Parts are to be installed per assembly procedure as outlined below.
4. Inside diameter and outside diameter of splice are to be measured in crimp area, 2.54 to 5.08mm
[0.100 to 0.200in] from ends of part. Slight burr permitted on parted surfaces.
5. Acceptance sampling shall be in accordance with Paragraph 4.6.1 of SAE AS81824.
6. Packing and packaging shall be in accordance with Section 5, Level C, of SAE AS81824.
7. This document takes precedence over documents referenced herein.
ASSEMBLY PROCEDURE
1.0
2.0
SCOPE
This document outlines the procedure to be followed to obtain immersion resistant multiple wire butt
splices using Multi-Wire In-Line Splice Sealing system D-436-88/-90.
PROCEDURE
a)
Pass the wires to be attached to one barrel through the separate multi-wire seal (3). Pass the wires to be
attached to the other barrel through the sealing sleeve from the three hole insert end.
b) Strip wires 5/16” to 11/32” and crimp into splice using a Raychem AD-1377 crimp tool. Care must be
taken so that the wires remain untwisted between the splice and the separate multi-wire seal (3) or the
sealing sleeve cannot be positioned properly.
c) Position the separate multi-wire seal (3) as close as possible to the splice. Hold this piece in position by
squeezing the wires directly behind it, and slide the sealing sleeve over the assembly so that the
separate multi-wire seal (3) is as far inside the sleeve as possible.
d) Apply heat, using the recommended heat source, first to the separate multi-wire seal end, and then to
the other. Heat should be applied until insert melts and flows axially along the wire.
3.0
RECOMMENDED RAYCHEM HEATING TOOLS
Heater
Heat Gun CV-1981
Steinel HL-1802E
Reflector
PR52D
PR52D
Recommended
setting
7.5 - 8
8-9
Unless otherwise specified, dimensions are in millimeters. [Inches dimensions are shown in rackets]
DOCUMENT NO.:
D-436-88/-90
DCR NUMBER:
D060019
REV.:
B1
DATE:
16-Apr-11
SHEET:
2 of 2
Print Date: 9-May-11
? 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company. All Rights Reserved.
If this document is printed it becomes uncontrolled. Check for the latest revision.
相关PDF资料 |
PDF描述 |
|---|---|
| D-609-08 | BUTT SPLICE 16-12AWG YELLOW TIN |
| D-609-10 | BUTT SPLICE 20-16AWG BLUE NICKEL |
| D-609-13 | BUTT SPLICE 779-2680CMA BLUE |
| DB500BLK | PLUG MINI BANANA STACKING DOUBLE |
| DC002-10 | IC SENSOR REG/PWR SW 5.0V 6-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| D-436-88CS2897 | 制造商:TE Connectivity 功能描述:650132N004 |
| D-436-89 | 功能描述:焊料和屏蔽管 RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03 |
| D-436-89CS2705 | 功能描述:焊料和屏蔽管 RoHS:否 制造商:TE Connectivity / Raychem 类型:Shield Terminators 材料:Polyvinylidene Fluoride 内径:5.08 mm 长度:16.5 mm 最低收缩温度: 系列:S03 |
| D-436-89CS2897 | 制造商:TE Connectivity 功能描述:650133N004 |
| D-436-89CS2908 | 制造商:TE Connectivity 功能描述:650133N005 |
发布紧急采购，3分钟左右您将得到回复。