- 您现在的位置：买卖IC网 > Datasheet目录219 > D2FW-G283M (Omron Electronics Inc-EMC Div)SWITCH LONGLEVER SPST-NO 1A SLD Datasheet资料下载
参数资料
| 型号： | D2FW-G283M |
| 厂商： | Omron Electronics Inc-EMC Div |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | SWITCH LONGLEVER SPST-NO 1A SLD |
| 标准包装： | 20 |
| 系列： | D2FW-G |
| 电路： | SPST-NO |
| 开关功能： | 关-瞬时 |
| 触点额定电压： | 1A @ 30VDC |
| 触动器类型： | 按片，叶形 |
| 安装类型： | 底座安装 |
| 端接类型： | 导线引线 |
| 操作力： | 300gf |
| 其它名称： | D2FWG283M SW514 |
Precautions
Use the Switch within the specified electrical ratings. Using the
Switch outside of the rated values will not only shorten its service life
but may cause heat generation or fire damage. When turning the
power ON or OFF, use the rated voltage and current.
■ Enclosure Ratings
Do Not Use the Switch Underwater
The Switch was tested and found to meet the conditions necessary
to meet the following standard. The test checks for water intrusion
after immersion for a specified time period. The test does not check
for switching operation underwater.
IEC Publication 529, degree of protection IP67.
Protection Against Chemicals
Prevent the Switch from coming into contact with oil or chemicals, to
avoid damaging (or deterioration of) Switch materials.
■ Mounting
Preparation for Mounting
Turn the power OFF before (1) mounting or removing the Switch, or
(2) before performing maintenance or inspection. Failure to do so can
cause electrical shock or fire.
Mount the Switch on a flat surface. If it is mounted on an uneven sur-
face the Switch may bend, causing a malfunction or cracking the
housing.
Mounting the Switch
Mount the switch securely, using an M4 screw with a flat washer or
spring washer. Tighten the screw to a torque of 1.18 to 1.47 N S m.
When mounting the switch, do not apply any external pressure to the
actuator in a direction other than the direction of operation.
The following diagram shows the mounting hole dimensions.
Mounting Holes
■ Operation
Make sure that the switching object is perfectly separated from the
actuator when the switch is not operated and the actuator is pressed
appropriately by the switching object when the switch is operated.
The switching object must not move beyond its operational limit posi-
tion.
Position the switching object so that its moving direction is the same
as that of the actuator.
■ Using the Switch with Micro
Loads
Even when the Switch is used within the appropriate operating
range, power surges may shorten its service life. Insert a contact pro-
tection circuit as required.
Micro application loads are indicated by N standard reference values.
This value represents the failure rate at a 60% ( λ 60) reliability level.
(JIS C5003)
The equation λ 60 = 0.5 x 10 -6 /operations indicates that a failure rate
of 1/2,000,000 operations can be expected at a reliability level of
60%.
4
Watertight Snap Action Switch D2FW-G
Model
Micro application load
D2FW-G0 j
5 VDC, 1 mA
D2FW-G2 j
5 VDC, 100 mA
相关PDF资料 |
PDF描述 |
|---|---|
| D2HW-BR202M | SWITCH SPDT-NC 2A RT LEADS |
| D2HW-C243MR | SWITCH BASIC SPST-NO SCREW SEAL |
| D2JW-01K1A1-MD | SWITCH BASIC SPDT .1A 117GF |
| D2MQ-1L-105 | SWITCH MINI SPDT 50MA 60GF PCB |
| D2MV-01L22-1C1 | BASIC SWITCH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| D2G | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:1.0A GLASS PASSIVATED RECTIFIER |
| D2G133-DB05-05 | 制造商:ebm-papst Inc 功能描述:- Bulk |
| D2G-T | 功能描述:整流器 1.0A 100V RoHS:否 制造商:Vishay Semiconductors 产品:Standard Recovery Rectifiers 配置: 反向电压:100 V 正向电压下降: 恢复时间:1.2 us 正向连续电流:2 A 最大浪涌电流:35 A 反向电流 IR:5 uA 安装风格:SMD/SMT 封装 / 箱体:DO-221AC 封装:Reel |
| D2H6 | 功能描述:电线导管 Sld Duct Dividr Wall PVC 2"H X 6’ RoHS:否 制造商:Panduit 类型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 颜色:Light Gray 大小: 最大光束直径: 抗拉强度: 外部导管宽度:25 mm 外部导管高度:25 mm |
| D2HS-14474-BA | 制造商:Ford Motor Company 功能描述:TERM F 56 SER |
发布紧急采购，3分钟左右您将得到回复。