- 您现在的位置：买卖IC网 > PDF目录237662 > D2SW-P01L1H SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 30VDC, 0.8mm, PANEL MOUNT PDF资料下载
参数资料
| 型号： | D2SW-P01L1H |
| 元件分类： | 开关 |
| 英文描述： | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 30VDC, 0.8mm, PANEL MOUNT |
| 文件页数： | 6/8页 |
| 文件大小： | 699K |
| 代理商： | D2SW-P01L1H |
6
Sealed Subminiature Basic Switch
D2SW-P
■ Correct Use
Mounting
Turn OFF the power supply before mounting or removing the Switch,
wiring, or performing maintenance or inspection. Failure to do so may
result in electric shock or burning.
Use M2.3 mounting screws with plane washers or spring washers to
securely mount the Switch. Tighten the screws to a torque of 0.23 to
0.26 Nm {2.3 to 2.7 kgfcm}. Exceeding the specified torque may
result in deterioration of the sealing or damage.
Mount the Switch onto a flat surface. Mounting on an uneven surface
may cause deformation of the Switch, resulting in faulty operation or
damage.
Operating Body
Use an operating body with low frictional resistance and of a shape
that will not interfere with the sealing rubber, otherwise the plunger
may be damaged or the sealing may deteriorate.
With the pin plunger models, set the Switch so that the plunger can
be pushed in from directly above. Since the plunger is covered with a
rubber cap, applying a force from lateral directions may cause dam-
age to the plunger or reduction in the sealing capability
.
Handling
Do not handle the Switch in a way that may cause damage to the
sealing rubber.
When handling the Switch, ensure that uneven pressure or, as
shown in the following diagram, pressure in a direction other than the
operating direction is not applied to the Actuator, otherwise the Actu-
ator or Switch may be damaged, or durability may be decreased.
Wiring Molded Lead Wire Models
When wiring molded lead wire models, ensure that there is no weight
on the wire or that there are no sharp bends near the parts where the
wire is drawn out. Otherwise, damage to the Switch or deterioration
in the sealing may result.
Operating Stroke Setting
Set the operating stroke so that the actuator is completely disen-
gaged when the switch is in the free position (FP), and is pushed to a
point between 60% and 90% of the OT distance after the switch is
operated.
Insufficient or excessive pushing of the actuator may result in
decreased switch durability or damage to the switch.
Using Micro Loads
Using a model for ordinary loads to open or close the contact of a
micro load circuit may result in a faulty contact. Use models that
operate in the following range. However, even when using micro load
models within the operating range shown below, if inrush current
occurs when the contact is opened or closed, it may increase contact
wear and so decrease durability. Therefore, insert a contact protec-
tion circuit where necessary. The minimum applicable load is the
N-level reference value. This value indicates the malfunction refer-
ence level for the reliability level of 60% (
λ60).
The equation,
λ60 = 0.5 x 10-6/operations indicates that the esti-
mated malfunction rate is less than 1/2,000,000 operations with a
reliability level of 60%.
Incorrect
Correct
30
24
12
5
0
1
10
100
1,000
0.1
1mA
26mA
0.16mA
100mA 160mA
100mA
V
o
ltage
(V)
Operating range for
micro load models
D2SW-P01
Operating
range for
general-load
models
D2SW-P2
Inoperable
range
Current (mA)
相关PDF资料 |
PDF描述 |
|---|---|
| D2SW-P2B | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 2A, 30VDC, 1mm, THROUGH HOLE-STRAIGHT |
| D368-S8KD | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 9.6mm, PANEL MOUNT |
| D368-S8LD | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 5.6mm, PANEL MOUNT |
| D371-W9KD | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 9.6mm, PANEL MOUNT |
| D379-W9JA | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 2.6mm, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| D2SWP01L1M | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT HINGE LVR WIRE LEAD 0.1A 125VAC 30VDC 0.6 - Trays 制造商:Omron Electronic Components LLC 功能描述:SUBMINIATURE BASIC SWITCH |
| D2SW-P01L1M | 功能描述:基本/快动开关 Subminiature Basic Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| D2SWP01L1T | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT HINGE LVR QC 0.1A 125VAC 30VDC 0.6N TH - Trays 制造商:Omron Electronic Components LLC 功能描述:SUBMINIATURE BASIC SWITCH |
| D2SW-P01L1T | 功能描述:基本/快动开关 Subminiature Basic Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| D2SW-P01L2B | 制造商:Omron Electronic Components LLC 功能描述:MICROSWITCH SPDT 0.1A SIM ROLLER 制造商:Omron Electronic Components LLC 功能描述:MICROSWITCH, SPDT, 0.1A, HINGE ROLLER 制造商:Omron Electronic Components LLC 功能描述:Switch,SPDT,roller lever,PCB term,0.1A |
发布紧急采购，3分钟左右您将得到回复。