- 您现在的位置：买卖IC网 > Datasheet目录219 > D2SW-P01L3-3M (Omron Electronics Inc-EMC Div)SWITCH SIM ROLL .1A SPST-NO WIRE Datasheet资料下载
参数资料
| 型号： | D2SW-P01L3-3M |
| 厂商： | Omron Electronics Inc-EMC Div |
| 文件页数： | 5/6页 |
| 文件大小： | 0K |
| 描述： | SWITCH SIM ROLL .1A SPST-NO WIRE |
| 标准包装： | 20 |
| 系列： | * |
| 其它名称： | D2SWP01L33M |
D2SW-P
Precautions
★ Please refer to "Basic Switches Common Precautions" for correct use.
Sealed Subminiature Basic Switch
Cautions
● Degree of Protection
? Do not use this product in water.
Although this models satisfy the test conditions for the
standard given below, this test is to check the ingress of water
into the switch enclosure after submerging the Switch in water
for a given time. Satisfying this test condition does not mean
that the Switch can be used in water.
JIS C0920:
Degrees of protection provided by enclosures of electrical
apparatus (IP Code)
IEC 60529:
Degrees of protection provided by enclosures (IP Code)
Degree of protection: IP67
(check water intrusion after immersion
for 30 min submerged 1 m
underwater)
? Do not operate the Switch when it is exposed to water spray,
or when water drops adhere to the Switch surface, or during
sudden temperature changes, otherwise water may intrude
into the interior of the Switch due to a suction effect.
? Prevent the Switch from coming into contact with oil and
chemicals.
Otherwise, damage to or deterioration of Switch materials may
result.
? Do not use the Switch in areas where it is exposed to silicon
adhesives, oil, or grease, otherwise faulty contact may result
due to the generation of silicon oxide.
? The environment-resistant performance of the switch differs
depending on operating loads, ambient atmospheres, and
installation conditions, etc. Please perform an operating test of
the switch in advance under actual usage conditions.
● Soldering
? Connecting to Solder Terminals
When soldering the lead wire to the terminal, first insert the
lead wire conductor through the terminal hole and then
conduct soldering.
Complete the soldering at the iron tip temperature between
350 to 400°C within 3 seconds, and do not apply any external
force for 1 minute after soldering. Soldering at a excessively
high temperature or soldering for more than 3 s may
deteriorate the characteristics of the Switch.
? Connecting to Quick-connect Terminals
Wire the quick-connect terminals (#110) with receptacles.
Insert the terminals straight into the receptacles. Applying
excessive external force laterally may cause deformation of
terminals and may damage the housings.
? Connecting to PCB terminals
When using automatic soldering baths, we recommend
soldering at 260 ± 5°C within 5 seconds. Make sure that the
liquid surface of the solder does not flow over the edge of the
board.
When soldering terminals manually, complete the soldering at
the iron tip temperature between 350 to 400°C within 3
seconds, and do not apply any external force for 1 minute after
soldering. When applying solder, keep the solder away from
the case of the Switch and do not allow solder or flux to flow
into the case.
● Side-actuated (Cam/Dog) Operation
? When using a cam or dog to operate the Switch, factors such
as the operating speed, operating frequency, push-button
indentation, and material and shape of the cam or dog will
affect the durability of the Switch. Confirm performance
specifications under actual operation conditions before using
the Switch in applications.
Correct Use
● Mounting
? Turn OFF the power supply before mounting or removing the
Switch, wiring, or performing maintenance or inspection.
Failure to do so may result in electric shock or burning.
? Use M2.3 mounting screws with plane washers or spring
washers to securely mount the Switch.
Tighten the screws to a torque of 0.23 to 0.26 N·m {2.3 to
2.7 kgf·cm}. Exceeding the specified torque may result in
deterioration of the sealing or damage.
● Operating Body
? Use an operating body with low frictional resistance and of a
shape that will not interfere with the sealing rubber, otherwise
the plunger may be damaged or the sealing may deteriorate.
With the pin plunger models, set the Switch so that the plunger
can be pushed in from directly above. Since the plunger is
covered with a rubber cap, applying a force from lateral
directions may cause damage to the plunger or reduction in
the sealing capability. Since the plunger is covered with a
rubber cap, applying a force from lateral directions may cause
damage to the plunger or reduction in the sealing capability.
● Handling
? Do not handle the Switch in a way that may cause damage to
the sealing rubber.
? When handling the Switch, ensure that uneven pressure or, as
shown in the following diagram, pressure in a direction other
than the operating direction is not applied to the Actuator,
otherwise the Actuator or Switch may be damaged, or
durability may be decreased.
● Wiring Molded Lead Wire Models
? When wiring molded lead wire models, ensure that there is no
force applied on the wire or that there are no sharp bends near
the parts where the wire is drawn out.
Otherwise, damage to the Switch or deterioration in the
sealing may result.
5
相关PDF资料 |
PDF描述 |
|---|---|
| D2T-LKT1-1 | BASIC SWITCH |
| D2VW-01-3MS | MINIATURE BASIC SWITCH |
| D2VW-01L1B-3MS | SWITCH HINGE SPDT-NO .1A WIRE |
| D2X | SWITCH HORZ LEVER SPST-NC .1A |
| D3C-2210 | SWITCH SPDT BASIC 130GF SHORTING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| D2SWP01L3B | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT SIMULATED ER LVR PC PINS 0.1A 125VAC 30VD - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH SIM ROLLER SPDT .1A PCB |
| D2SW-P01L3B | 功能描述:基本/快动开关 Sim roller levr 61gf Sealed PCB even 0.1A RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| D2SWP01L3D | 制造商:Omron Electronic Components LLC 功能描述:SWITCH;SUBMINIATURE,SNAP ACTION,LIMIT SWITCH SIM ROLLER LEVR 61GF SEALED PCB 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT SIMULATED ER LVR PC PINS 0.1A 125VAC 30VD - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH SIM ROLLER SPDT .1A PCB |
| D2SW-P01L3D | 功能描述:基本/快动开关 Sim roller levr 61gf Sealed PCB unevn .1A RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| D2SW-P01L3H | 制造商:Omron Electronic Components LLC 功能描述:MICROSWITCH SPDT 0.1A SIM ROLLER 制造商:Omron Electronic Components LLC 功能描述:MICROSWITCH, SPDT, 0.1A, SIM ROLLER 制造商:Omron Electronic Components LLC 功能描述:Switch,SPDT,sim roller,solder trm,0.1A |
发布紧急采购，3分钟左右您将得到回复。