- 您现在的位置：买卖IC网 > PDF目录237684 > D4A-1E12N-F SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 10A, 14VDC, PANEL MOUNT PDF资料下载
参数资料
| 型号： | D4A-1E12N-F |
| 元件分类： | 开关 |
| 英文描述： | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 10A, 14VDC, PANEL MOUNT |
| 文件页数： | 14/24页 |
| 文件大小： | 945K |
| 代理商： | D4A-1E12N-F |
94
General-purpose Limit Switch
D4A-
@N
Precautions
■ Correct Use
Operating Environment
Seal material may deteriorate if a Switch is used outdoor or where
subject to special cutting oils, solvents, or chemicals. Always
appraise performance under actual application conditions and set
suitable maintenance and replacement periods.
Install Switches where they will not be directly subject to cutting
chips, dust, or dirt. The Actuator and Switch must also be protected
from the accumulation of cutting chips or sludge.
Constantly subjecting a Switch to vibration or shock can result in
wear, which can lead to contact interference with contacts, opera-
tion failure, reduced durability, and other problems. Excessive
vibration or shock can lead to false contact operation or damage.
Install Switches in locations not subject to shock and vibration and
in orientations that will not produce resonance.
The Switches have physical contacts. Using them in environments
containing silicon gas will result in the formation of silicon oxide
(SiO
2) due to arc energy. If silicon oxide accumulates on the con-
tacts, contact interference can occur. If silicon oil, silicon filling
agents, silicon cables, or other silicon products are present near
the Switch, suppress arcing with contact protective circuits (surge
killers) or remove the source of silicon gas.
Mounting
Tightening Torque
To maintain the high sealing capability of the Limit Switch, tighten the
screws for the head and switch box with the following torques:
Head (four 12-mm M4 screws): 1.2 to 1.4 Nm
Switch box (two 20-mm M5 screws): 2.4 to 2.7 Nm
Solderless Terminals
The D4A-
@N with DPDT double-break incorporates solderless
terminals.
Operation
The operating methods, cam and dog shapes, operating frequency,
and overtravel (OT) have a significant effect on the service life and
accuracy of the Limit Switch. The shape of the cam should be as
smooth as possible.
A marginal overtravel (OT) value should be set. The ideal value is the
rated OT value x 0.7.
The actuator should not be remodeled to change the operating
position.
Connectors
To satisfy IP67, apply sealing tape to the connector conduit.
Appropriate outer diameter of cables is 5.5 to 14 dia.
Use OMRON’s SC-
@M Series.
Tighten the Connectors to a torque of 1.8 to 2.2 Nm.
Maintenance and Repair
The user must not maintain or repair equipment incorporating any
D4A-N model. Contact the manufacturer of the equipment for any
maintenance or repairs required.
Tightening Torque
A loose screw may cause malfunctions. Be sure to tighten each
screw to the proper tightening torque as shown in the table.
Model
1/2-14NPT Conduit
D4A-1
@@@N
D4A-2
@@@N
Front Mounting
Rear Mounting
(Rear View)
Not Suitable
Suitable
59.5
±0.15
29.4
±0.15
0
Two, 5.2
+0.2 dia. holes
or M5 tapped holes
59.5
±0.15
29.4
±0.15
0
Two, 6.2
+0.2 dia. holes
(Recommended mount-
ing screws: M6.
Switch Box depth: 10.)
相关PDF资料 |
PDF描述 |
|---|---|
| DC2FK9RB | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 6.5mm, THROUGH HOLE-RIGHT ANGLE |
| DC2AE6LD | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, THROUGH HOLE-RIGHT ANGLE |
| D3SH-A1R1 | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 0.001A, 5VDC, 3.8mm, SURFACE MOUNT-RIGHT ANGLE |
| D2F-01FL2-A1 | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 30VDC, 0.55mm, THROUGH HOLE-RIGHT ANGLE |
| D2SW-P2L3D | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 2A, 30VDC, 0.8mm, THROUGH HOLE-STRAIGHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| D4A2000N | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:DPDT SWITCH RECEPTACLE 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:DPDT SWITCH RECEPTACLE |
| D4A-2000N | 功能描述:限位开关 DPDT SWITCH REC EPTACLE RoHS:否 制造商:Honeywell 触点形式:SPDT 执行器:Non-Contact 电流额定值:30 mA 电压额定值 AC: 电压额定值 DC:3.6 V 工作力:10 g IP 等级:IP 67 NEMA 额定值:1, 4, 12, 13 端接类型:4-Pin M12 Connector 安装:SMD/SMT |
| D4A2501N | 制造商:Omron Electronic Components LLC 功能描述:Switch Limit N.O./N.C. DPDT Side Roller Lever Conduit 5A 600VAC 250VDC Rotary Screw Mount 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Limit N.O./N.C. DPDT Side Roller Lever Conduit 5A 600VAC 250VDC Rotary Screw Mount |
| D4A-2501N | 功能描述:限位开关 DPDT SIDE ROTARY RoHS:否 制造商:Honeywell 触点形式:SPDT 执行器:Non-Contact 电流额定值:30 mA 电压额定值 AC: 电压额定值 DC:3.6 V 工作力:10 g IP 等级:IP 67 NEMA 额定值:1, 4, 12, 13 端接类型:4-Pin M12 Connector 安装:SMD/SMT |
| D4A-2501-N | 功能描述:LIMIT SWITCH DPDT ROLLER RoHS:是 类别:开关 >> 快动，限位，拉杆 系列:D4A 其它有关文件:Declaration of Conformity 标准包装:1 系列:* |
发布紧急采购，3分钟左右您将得到回复。