- 您现在的位置：买卖IC网 > PDF目录17031 > DC1500A-A (Linear Technology)BOARD SAR ADC LTC2393-16 PDF资料下载
参数资料
| 型号： | DC1500A-A |
| 厂商： | Linear Technology |
| 文件页数： | 23/24页 |
| 文件大小： | 0K |
| 描述： | BOARD SAR ADC LTC2393-16 |
| 软件下载： | QuikEval II System |
| 设计资源： | DC1500A Design File DC1500A Schematic |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 1M |
| 数据接口： | 串行，并联 |
| 输入范围： | ±4.096 V |
| 在以下条件下的电源（标准）： | 140mW @ 1MSPS |
| 工作温度： | 0°C ~ 70°C |
| 已用 IC / 零件： | LTC2393-16 |
| 已供物品： | 板 |
| 相关产品： | DC718C-ND - DEMO QUIKEVAL-II DATA LTC2393IUK-16#TRPBF-ND - IC ADC 16BIT SER/PAR 1M 48-QFN LTC2393CUK-16#TRPBF-ND - IC ADC 16BIT SER/PAR 1M 48-QFN LTC2393ILX-16#PBF-ND - IC ADC 16BIT SER/PAR 1M 48-LQFP LTC2393IUK-16#PBF-ND - IC ADC 16BIT SER/PAR 1M 48-QFN LTC2393HLX-16#PBF-ND - IC ADC 16BIT SER/PAR 1M 48-LQFP LTC2393CUK-16#PBF-ND - IC ADC 16BIT SER/PAR 1M 48-QFN LTC2393CLX-16#PBF-ND - IC ADC 16BIT SER/PAR 1M 48-LQFP |
LTC2393-16
8
239316fa
PIN FUNCTIONS
GND (Pins 1, 5, 7, 20, 35, 41, 44, 48, Exposed Pad
Pin 49 (QFN Only)): Ground. All GND pins must be con-
nected to a solid ground plane. Exposed pad must be
soldered directly to the ground plane.
AVP (Pins 2, 40, 45, 46, 47): 5V Analog Power Supply.
The range of AVP is 4.75V to 5.25V. Bypass AVP to GND
with a good quality 0.1μF and a 10μF ceramic capacitor
in parallel.
DVP (Pins 3, 19): 5V Digital Power Supply. The range of
DVP is 4.75V to 5.25V. Bypass DVP to GND with a good
quality 0.1μF and a 10μF ceramic capacitor in parallel.
SER/PAR (Pin 4): Serial/Parallel Selection Input. This pin
controls the digital interface. A logic high on this pin se-
lects the serial interface and a logic low selects the parallel
interface. In the serial mode the non-active digital outputs
are high impedance.
OB/2C (Pin 6): Offset Binary/Two’s Complement Input.
When OB/2C is high, the digital output is offset binary.
When low, the MSB is inverted resulting in two’s comple-
ment output.
BYTESWAP (Pin 8): BYTESWAP Input. With BYTESWAP
low, data will be output with Pin 28 (D15) being the MSB
and Pin 9 (D0) being the LSB. With BYTESWAP high, the
upper eight bits and the lower eight bits will be switched.
The MSB is output on Pin 16 and Bit 8 is output on Pin 9.
Bit 7 is output on Pin 28 and the LSB is output on Pin 21.
D0 (Pin 9): Data Bit 0. When SER/PAR = 0 this pin is Bit 0
of the parallel port data output bus.
D1 (Pin 10): Data Bit 1. When SER/PAR = 0 this pin is
Bit 1 of the parallel port data output bus.
D2 (Pin 11): Data Bit 2. When SER/PAR = 0 this pin is
Bit 2 of the parallel port data output bus.
D3 (Pin 12): Data Bit 3. When SER/PAR = 0 this pin is
Bit 3 of the parallel port data output bus.
D4 (Pin 13): Data Bit 4. When SER/PAR = 0 this pin is
Bit 4 of the parallel port data output bus.
D5 (Pin 14): Data Bit 5. When SER/PAR = 0 this pin is
Bit 5 of the parallel port data output bus.
D6 (Pin 15): Data Bit 6. When SER/PAR = 0 this pin is
Bit 6 of the parallel port data output bus.
D7 (Pin 16): Data Bit 7. When SER/PAR = 0 this pin is
Bit 7 of the parallel port data output bus.
OGND (Pin 17): Digital Ground for the Input/Output
Interface.
OVP (Pin 18): Digital Power Supply for the Input/Output
Interface. The range for OVP is 1.8V to 5V. Bypass OVP
to OGND with a good quality 4.7μF ceramic capacitor
close to the pin.
D8 (Pin 21): Data Bit 8. When SER/PAR = 0 this pin is
Bit 8 of the parallel port data output bus.
D9/SDIN (Pin 22): Data Bit 9/Serial Data Input. When SER/
PAR = 0 this pin is Bit 9 of the parallel port data output bus.
When SER/PAR = 1, (serial mode) this is the serial data
input. SDIN can be used as a data input to daisy chain two
or more conversion results into a single SDOUT line. The
digital data level on SDIN is output on SDOUT with a delay
of 16 SCLK periods after the start of the read sequence.
D10/SDOUT (Pin 23): Data Bit 10/Serial Data Output. When
SER/PAR = 0 this pin is Bit 10 of the parallel port data
output bus. When SER/PAR = 1, (serial mode) this is the
serial data output. The conversion result can be clocked
out serially on this pin synchronized to SCLK. The data
is clocked out MSB first on the rising edge of SCLK and
is valid on the falling edge of SCLK. The data format is
determined by the logic level of OB/2C.
D11/SCLK (Pin 24): Data Bit 11/Serial Clock Input. When
SER/PAR = 0 this pin is Bit 11 of the parallel port data
output bus. When SER/PAR = 1, (serial mode) this is the
serial clock input.
D12 (Pin 25): Data Bit 12. When SER/PAR = 0 this pin is
Bit 12 of the parallel port data output bus.
D13 (Pin 26): Data Bit 13. When SER/PAR = 0 this pin is
Bit 13 of the parallel port data output bus.
D14 (Pin 27): Data Bit 14. When SER/PAR = 0 this pin is
Bit 14 of the parallel port data output bus.
D15 (Pin 28): Data Bit 15. When SER/PAR = 0 this pin is
Bit 15 of the parallel port data output bus. The data format
is determined by the logic level of OB/2C.
相关PDF资料 |
PDF描述 |
|---|---|
| STD17W-V | WIRE & CABLE MARKERS |
| MLG1005S47NJ | INDUCTOR MULTILAYER 47NH 0402 |
| STD17W-D | WIRE & CABLE MARKERS |
| STD17W-J | WIRE & CABLE MARKERS |
| STD17W-6 | WIRE & CABLE MARKERS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1500A-A | 制造商:Linear Technology 功能描述:LTC2393-16 W/ LT6350 OPTIMIZED DRIVER 5 |
| DC1500A-B | 功能描述:BOARD SAR ADC LTC2392-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1500A-C | 功能描述:BOARD SAR ADC LTC2391-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1500B2 PK2 | 制造商:Duracell 功能描述:Battery, Rechargeable, Nickel Metal Hydride, AA cell, 2 pk, 1.2 V |
| DC1500B4 PK4 | 制造商:Duracell 功能描述:Battery, Rechargeable, Nickel Metal Hydride, AA cell, 4 PK, 1.2 V |
发布紧急采购，3分钟左右您将得到回复。