参数资料
型号: DEMOBOARD TLE 6368
厂商: Infineon Technologies
文件页数: 16/59页
文件大小: 0K
描述: BOARD DEMO FOR TLE 6368
标准包装: 1
主要目的: DC/DC,LDO 步降
输入电压: 5.5 ~ 60 V
稳压器拓扑结构: 降压
板类型: 完全填充
已供物品:
已用 IC / 零件: TLE6368
相关产品: TLE6368R-ND - IC PS SYSTEM MULTI VOLT PDSO-36
TLE6368G1-ND - IC PS SYSTEM MULTI VOLT PDSO-36
其它名称: DEMOBOARDTLE6368IN
TLE 6368 / SONIC
the closed window (CW) starts. Then three valid watchdog triggers are shown, no effect
on the reset line and/or error pin is observed. With the missing watchdog trigger signal
the error signal turns low immediately where the reset is asserted after another delay of
half the closed window time.
Also shown in the figure are two typical failure modes, one pretrigger and one missing
signal. In both cases the error signal will go low immediately the failure is detected with
the reset following after the half closed window time.
2.10
Overtemperature Protection
At a chip temperature of more than 150° an error and temperature flag is set and can be
read through the SPI. The device is switched off if the device reaches the
overtemperature threshold of 170°C. The overtemperature shutdown has a hysteresis to
avoid thermal pumping.
2.11
Power Down Mode
The TLE 6368 G1 / SONIC is started by a static high signal at the wake input or a high
pulse with a minimum of 50μs duration at the Wake input (pin 34). Voltages in the range
between the turn on and turn off thresholds for a few 100μs must be avoided!
By SPI command (“Sleep”-bit, D8, equals zero) all voltage regulators including the
switching regulator except the standby regulator can be turned off completely only if the
wake input is low. In the case the Wake input is permanently connected to battery the
device cannot be turned off by SPI command, it will always turn on again.
For stable “on” operation of the device the “Sleep”-bit, D8 has to be set to high at each
SPI cycle!
When powering the device again after power down the status of the SPI controlled
devices (e.g. trackers, watchdog etc.) depends on the output voltage on Q_LDO1. Did
the voltage at Q_LDO1 decrease below 3.3V the default status (given in the next section)
is set otherwise the last SPI command defines the status.
2.12
Serial Peripheral Interface
A standard 16 bit SPI is available for control and diagnostics. It is capable to operate in
a daisy chain. It can be written or read by a 16 bit SPI interface as well as by an 8 bit SPI
interface.
The 16-bit control word (write bit assignment, see Figure 8) is read in via the data input
DI, synchronous to the clock input CLK supplied by the μC beginning with the LSB D0.
The diagnosis word appears in the same way synchronously at the data output DO (read
bit assignment, see figure 9), so with the first bit shifted on the DI line the first bit appears
on the DO line.
The transmission cycle begins when the TLE 6368 G1 / SONIC is selected by the “not
chip select” input CS (H to L). After the CS input returns from L to H, the word that has
Data Sheet
16
Rev. 2.2, 2006-12-01
相关PDF资料
PDF描述
RBC07DREH-S13 CONN EDGECARD 14POS .100 EXTEND
GBC31DCMD-S288 CONN EDGECARD 62POS .100 EXTEND
GEC13DRYI-S13 CONN EDGECARD 26POS .100 EXTEND
GBC08DRYI-S13 CONN EDGECARD 16POS .100 EXTEND
ESC05DRTS-S13 CONN EDGECARD 10POS .100 EXTEND
相关代理商/技术参数
参数描述
DEMOBOARD-U2790B 功能描述:射频开发工具 COM-I/Q MODULATOR 1GHZ RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
DEMOBOARD-U2793B 功能描述:射频开发工具 COM-I/Q MODULATOR 300MHZ RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
DEMOBOARD-U2794B 功能描述:射频开发工具 COM-I/Q DEMODULATOR 1GHZ RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
DEMOBOARD-U3600BM 功能描述:射频开发工具 COM-ONE CHIP CT0 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
DEMOBOARD-U3761MB 功能描述:BOARD DEMO FOR U3761MB RoHS:否 类别:编程器,开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK(80-QFP ZIF 插口) 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035