- 您现在的位置：买卖IC网 > PDF目录1911 > DG413FEUE+ (Maxim Integrated Products)IC SWITCH QUAD SPST 16TSSOP PDF资料下载
参数资料
| 型号： | DG413FEUE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/16页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH QUAD SPST 16TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 功能： | 开关 |
| 电路： | 4 x SPST - NC/NO |
| 导通状态电阻： | 85 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 9 V ~ 36 V，±4.5 V ~ 20 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
DG411F/DG412F/DG413F
the switch state. If the switch state is off, all FETs are
turned off and both NO_ (or NC_) and COM_ are high
impedance.
Negative Fault Condition
When the signal on NO_ (or NC_) and COM_ exceeds
V- by about 50mV, the low-fault comparator output is
high, turning off FETs N1 and P1. This makes the NO_
(or NC_) and COM_ pins high impedance regardless of
the switch state. If the switch state is off, all FETs are
turned off and both NO_ (or NC_) and COM_ are high
impedance.
Transient Fault Response and Recovery
When a fast rise-time and fall-time transient on NO_,
NC_, or COM_ exceeds V+ or V-, the output follows the
input to the supply rail with only a few nanoseconds
delay. This delay is due to the switch on-resistance and
circuit capacitance to ground. When the input transient
returns to within the supply rails, however, there is a
longer output recovery time delay. For positive faults,
the recovery time is typically 1s. For negative faults,
the recovery time is typically 0.5s. These values
depend on the output resistance and capacitance, and
are not production tested or guaranteed. The delays
are not dependent on the fault amplitude. Higher load
resistance and capacitance increase recovery times.
Fault-Protection Voltage and Power Off
The maximum fault voltage on the NO_ (or NC_) and
COM_ pins is ±36V with power applied and ±40V with
power off.
Failure Modes
Exceeding the fault-protection voltage limits on NO_,
NC_, or COM_, even for very short periods, can cause
the device to fail. See the Absolute Maximum Ratings.
The failure modes may not be obvious, and failure in
one switch may or may not affect other switches in the
same package.
Ground
There is no galvanic connection between the analog
signal paths and GND. The analog signal paths consist
of an N-channel and P-channel MOSFET with their
sources and drains paralleled and their gates driven
out of phase to V+ and V- by the logic-level translators.
However, the potential of the analog signals must be
defined or at least limited with respect to GND.
V+ and GND power the internal logic and logic-level
translators and set the input logic thresholds. The logic-
level translators convert the logic levels to switched V+
and V- signals to drive the gates of the analog switch-
es. This drive signal is the only connection between the
power supplies and the analog signals.
IN_ Logic-Level Thresholds
The logic-level thresholds are CMOS and TTL compati-
ble when V+ is +15V. As V+ is raised, the threshold
increases slightly, and when V+ reaches 25V, the level
threshold is about 2.3V, above the TTL output high-level
minimum of 2.4V, but still compatible with CMOS out-
puts (see the Typical Operating Characteristics). V- has
no effect on the logic-level thresholds.
Bipolar Supplies
The DG411F/DG412F/DG413F operate with bipolar
supplies between ±4.5V and ±20V. The V+ and V- sup-
plies need not be symmetrical, but their difference can-
not exceed the absolute maximum rating of 44V.
Single Supply
The DG411F/DG412F/DG413F operate from a single
supply between +9V and +36V when V- is connected to
GND.
Chip Information
TRANSISTOR COUNT: 251
PROCESS: CMOS
SUBSTRATE CONNECTED TO: V+
Quad, Rail-to-Rail, Fault-Protected,
SPST Analog Switches
10
______________________________________________________________________________________
Ordering Information (continued)
PART
TEMP RANGE
PIN-PACKAGE
DG412FEUE
-40°C to +85°C
16 TSSOP
DG412FDY
-40°C to +85°C
16 SO
DG412FDJ
-40°C to +85°C
16 Plastic DIP
DG413FEUE
-40°C to +85°C
16 TSSOP
DG413FDY
-40°C to +85°C
16 SO
DG413FDJ
-40°C to +85°C
16 Plastic DIP
相关PDF资料 |
PDF描述 |
|---|---|
| DG4157DN-T1-E4 | IC SWITCH SGL SPDT LV 6-MINIQFN |
| DG418BDJ-E3 | IC ANALOG SWITCH SPDT 8DIP |
| DG418DY-T1-E3 | IC ANALOG SWITCH CMOS 8SOIC |
| DG418LDY-E3 | IC ANALOG SWITCH CMOS 8SOIC |
| DG418LEUA+ | IC SWITCH SPST 8UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DG413FEUE+ | 功能描述:模拟开关 IC Quad SPST Open/Closed RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| DG413FEUE+T | 功能描述:模拟开关 IC Quad SPST Open/Closed RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| DG413FEUE-T | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| DG413HS | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Precision Monolithic Quad SPST CMOS Analog Switches |
| DG413HSAK | 制造商:Vishay Siliconix 功能描述:IC SWITCH QUAD SPST 16-SOIC |
发布紧急采购，3分钟左右您将得到回复。