- 您现在的位置：买卖IC网 > PDF目录258068 > DHC2805S (MS KENNEDY CORP) 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | DHC2805S |
| 厂商： | MS KENNEDY CORP |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | HERMETICALLY SEALED, DIP-8 |
| 文件页数： | 5/9页 |
| 文件大小： | 259K |
| 代理商： | DHC2805S |
APPLICATION NOTES
POWER SUPPLIES
The output voltage of the DHC2800S may be adjusted from
90% to 110% of nominal value by the use of a 50K
potenti-
ometer as shown. Adjustment beyond this range is possible
however certain characteristics of the converter such as but
not limited to input voltage range, efficiency, ripple and tem-
perature performance will change. Characterization by the user
is recommended in such applications.
Adjust/comp (pin 3) may be driven by external circuitry refer-
enced to pin 2 (-output) if desired.
Grounding pin 3 causes
voltage to increase (25% typically) while driving pin 3 above
1.3V causes output voltage to decrease. Pin 3 may be driven
through 10K
or more if connection of the comp function is
also required.
The comp function of pin 3 allows capacitive loads as large
as 1000F to be accommodated on the DHC2805S without
loss of stability. This feature may be utilized by connecting a
10nF capacitor between pins 3 and 1. This is generally recom-
mended when low ESR load capacitances of 100F or greater
are used.
Rev. D 12/03
5
SHUTDOWN PLUS
Pin 5 is used for remote shutdown, output fault detection,
and/or setting the input voltage point at which the converter
will turn on as shown in the typical application diagram. No
connection to pin 5 is necessary for normal operation of the
converter. Pin 5 is referenced to the -input (pin 7).
Shutdown may be implemented by simply connecting pin 5
to an open collector logic output or switch rated at 2.5mA,
25Vdc or higher.
Input voltage turn on point is programmed with a single resis-
tor from pin 5 to 7. An input turn on/off hysteresis (typically
3.5% of Vin) will be observed. This should be considered when
making or verifying set point adjustment.
The value of the
setpoint resistor may be determined by the following:
R=
(±10% accuracy at 25°C)
Set point temperature coefficient is typically +400ppm/°C.
Output fault monitoring is accomplished by observing pin 5
with a high impedance monitoring circuit. Pin 5 voltage drops
from over 10V to below 1V when a load fault causes the con-
verters fault protection circuitry to activate. It will remain low
for at least 100mS and return high.
If the load fault is still
present pin 5 will return low and the cycle will repeat. A resis-
tor >400K
from pin 5 to 7 provides pull down for pin 5 if
there is no input setpoint programming resistor already in place.
21010
ETO-9.5
LOAD FAULT RESPONSE
The DHC2800S series of dc-dc converters share load fault
philosophies.
Load fault conditions include short-circuit and
severe overload conditions. The DHC2800S converter series
responds to load faults by turning off all power conversion cir-
cuits for 250mS and then attempting to restart for 10mS (typi-
cal). The net "on" duty factor during a fault is very low result-
ing in low converter dissipation and immunity from overheating
at 125°C.
Current beyond rated can flow into the load at
startup time. This allows the converter to bring up capacitive
and other difficult load types more reliably than competing con-
verters.
相关PDF资料 |
PDF描述 |
|---|---|
| DM1501-9RD5AFU | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| DM1601-7RD6AFU | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| DM1901-7RD5AFU | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| DM3020-9PD7AFU | 3-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| DM3040-7PD8AFU | 3-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DHC2805SE | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:6W DC-DC CONVERTERS |
| DHC2805SH | 制造商:MSK 制造商全称:M.S. Kennedy Corporation 功能描述:6W DC-DC CONVERTERS |
| DHC2805SK | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DHC2812D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DC-to-DC Voltage Converter |
| DHC2812S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DC-to-DC Voltage Converter |
发布紧急采购，3分钟左右您将得到回复。