参数资料
| 型号： | DM300022 |
| 厂商： | Microchip Technology |
| 文件页数： | 26/56页 |
| 文件大小： | 0K |
| 描述： | MODULE PWR DSPICDEM MC1L LV 3PHS |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电机控制 |
| 嵌入式： | 是，MCU，16 位 |
| 已用 IC / 零件： | dsPIC33FJxxxMC |
| 主要属性： | 3 相低压电源模块 |
| 次要属性： | 运动传感器输入：霍尔传感器或光学编码器 |
| 已供物品： | 子板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
dsPICDEM? MC1L 3-Phase Low Voltage Power Module
1.5.6
1.5.6.1
Shunt Feedback (Appendix A Sheet 3)
INTRODUCTION
In many applications, the cost of isolated current transducers is prohibitive or the
isolation is not required. In these instances, it is common practice to use resistive
shunts. The shunts can be placed in series with the output connections, but this
inevitably requires the use of level-shifting and the creation of floating power supplies.
Therefore, it is more usual to have shunts referenced to the same potential as the low
voltage power supplies which is invariably the -DC bus. The disadvantage of using
shunts referenced to the low side is that the feedback information is clearly only
available during certain portions of the PWM cycle. In order to extract the required
information, the shunts must be sampled at precise intervals. This feature has been
allowed for in the dsPIC device by the inclusion of sample and hold amplifiers in the
ADC module that can be triggered from the PWM module (see the dsPIC30F Family
Reference Manual for details).
On high voltage low power systems, it may be possible to use shunts of high enough
value to have sufficient voltage for direct input to an ADC. More commonly, the
dissipation in the shunt dictates the use of low resistance values and appropriate
amplification. If too high, the voltage drop across the shunt can also cause problems
for driving the power transistors. For low gains, it may be possible to use single ended
amplification. Differential amplification is required as the gains increase in order to
provide a signal of sufficient quality and accuracy.
The Microchip MCP6022 (dual) and MCP6024 (quad) parts have been used in the
design for providing the differential amplification. They are an ideal choice for the
following reasons:
? Low power consumption (1 mA typical / amp) - this is especially important where
the power supplies are derived from the DC bus with a resistor/zener network.
? Low offset voltage (0.5 mV max.).
? Rail-rail inputs and outputs.
? No gain inversion with negative inputs - this is important as it is common for the
amplifier to have negative spikes on it's inputs that occur during switching events
due to the shunt's inductance. Gain inversion can lead to current control instability
and false tripping of protection circuits.
? High gain bandwidth product (10 MHz typical) - this is often a more important
factor in determining the speed of response than slew rate in this application, due
to the requirements to amplify rapidly changing signals of low amplitude.
Note that in applications requiring less gain and/or slower speed of response, the
MCP602/604 family offers a good alternative with even lower power supply
consumption.
1.5.6.2
INVERTER LEG SHUNT RESISTOR FEEDBACK
A shunt is located between the source of the low side switches (e.g., Q4) and the -DC
bus in every leg of the inverter. A simple differential amplifier circuit is used as shown
in Appendix A Sheet 3. The operation of the circuit used for the RED phase leg is
described below:
? U24-A – One quarter of the MC6024 op amp.
? R94, R99 and C34 – These provide a small amount of passive differential filtering.
This helps to reduce input stage overloading of the op amp that would occur due
to spikes of voltage produced by the shunt's self-inductance. Clearly, this has a
beneficial effect on the output signal.
DS70097A-page 20
? 2003 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| DM320002 | BOARD EXPANSION PIC32 I/O |
| DM320003-2 | KIT EVAL PIC32 USB II STARTER |
| DM320003 | BOARD DEMO USB PIC32 OTG |
| DM320005 | BOARD EXPANSION FOR PIC32 KIT |
| DM320011 | BOARD AUDIO DEV FOR PIC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DM300023 | 功能描述:开发板和工具包 - PIC / DSPIC dsPICDEM SMPS Buck Demo Brd RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
| DM300024 | 功能描述:开发板和工具包 - PIC / DSPIC dsPICDEM 1.1 GP RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
| DM300027 | 功能描述:开发板和工具包 - PIC / DSPIC 16-bit Starter Demo Board RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
| DM-3-000-K | 制造商:PacTec 功能描述:Case, Plastic; ABS; Black; 11.46 in.; 3.38 in.; 10.4 in.; UL 94-HB Rated 制造商:PacTec 功能描述:ENCLOSURE, DESKTOP, PLASTIC, BLACK; Enclosure Type:Desktop; Enclosure Material:Plastic; Body Color:Black; External Height - Imperial:3.38"; External Height - Metric:86mm; External Width - Imperial:10.4"; External Width - Metric:264mm;RoHS Compliant: Yes |
| DM-300-C | 制造商:Greenlee Textron Inc 功能描述:DMM 1000V RMS |
发布紧急采购，3分钟左右您将得到回复。