参数资料
型号: DMS-20LCD-0-9-C
厂商: Murata Power Solutions Inc
文件页数: 3/6页
文件大小: 0K
描述: DPM LCD 200MV 3.5DIG 9-14V SUPP
产品目录绘图: Digital Panel Meter
3D 型号: DMS-20LCD Series.pdf
DMS-20LCD Series.sldprt
DMS-20LCD Series.stp
DMS-20LCD Series.igs
标准包装: 12
系列: DMS-20LCD
类型: 伏特表
测量范围: ±200mV
显示器样式: 黑色字符,灰色背景
显示器类型: LCD
显示器正面尺寸: 1.30" L x 0.80" W(33.0 x 20.3mm)
显示器位数: 3.5
显示器位数 - 高度: 0.370"(9.40mm)
背光:
安装类型: 面板安装
端子: PC 引脚
电源电压: 9V
产品目录页面: 2855 (CN2011-ZH PDF)
其它名称: 811-1018
DMS-20LCD Series
3? Digit, LCD Display Digital Panel Voltmeters
point location pins should be left open. For 5V-powered models, the
8. Suggested Mating Connectors:
decimal location pins are TTL compatible and may be hard wired as
described above or driven with 5V TTL logic gates.
4. BACKLIGHT (Pin 9) Function: Grounding pin 9 (i.e. connecting it to
pin 3) turns on the backlighting LED’s. For non-backlit models, pin 9
has no internal connection. All backlit models include internal current-
limiting resistors. With nominal +5V or 9V supplies, backlit devices
typically draw 35mA of supply current. The current drawn by the back-
light (and therefore the current drawn by the meter) can be reduced by
installing a 1/4 Watt resistor between pins 3 and 9. The brightness of
the meter will be reduced proportionately.
Panel mounted:
Connector housing
Terminal type
Crimping tool
Wire size
Insulation diameter
Stripping length
Board mounted:
Socket
DATEL P/N 4320-01069-0
DATEL P/N 4400-01032-0
DATEL P/N 39-2099000
22 to 26 AWG
0.062” (1.57mm) maximum
0.100 to 0.125” (2.54 to 3.17mm)
DATEL P/N 4320-01074-0
9V-powered backlit models function with supply voltages up to +14V,
however, activating the backlight with voltages greater than 9.2V can
damage the meter. Therefore, a 1/4 Watt series resistor must be
installed between pins 3 and 9 in these situations. The value of the
series resistor is determined using the following formula:
APPLICATIONS
DMS-20LCD meters are available in either 5V-powered or 9V-powered
models. 9V devices operate directly from 7.5V to 14V supplies (usually
batteries) without the need for external voltage regulators. 9V devices,
however, can not be used to measure voltages referenced to the negative
R Series =
+BATTERY – 9.2V
0.035
Ohms
battery terminal (pin 3) because the minus input to the meter (pin 12, (–)
INPUT LO) must always be at least 1.5V above pin 3. 9V-powered meters
Example: If +BATTERY (pin 1 with respect to pin 3) is +12.6V,
can only be used to make differential and not single-ended measurements.
5V-powered devices operate from any well-regulated +5V supply and will
R Series =
+12.6 – 9.2V
0.035
Ohms
accurately measure voltages both above and below pin 3 (5V RETURN) in
either single-ended or differential con?gurations.
R Series = 97 Ohms
5. Low Battery Annunciator: The “B” annunciator in the upper left-hand
corner of the display turns on when the supply voltage for 5V-powered
models falls below approximately +3.7V, or when the supply voltage for
9V-powered models falls below approximately 7.2V. However, the low-
battery annunciator’s turn-on threshold can vary signi?cantly from unit-
1. Single-Ended Input Con?gurations: True single-ended measure-
ments can only be made with 5V-powered meters. The circuit of Figure
2 avoids problems normally associated with ground-loop currents.
Separate ground runs should be used for 5V RETURN (pin 3) and (–)
INPUT LO (pin 12).
to-unit: as low as 2.7V for 5V-powered meters, and as low as 5.4V for
9V-powered models. Applications that use the LOW BAT annunciator
must be fully tested by the user, using a combination of low supply volt-
+
11
(+) IN HI
DMS-20LCD-1-5
8
REF OUT
ages and the input signal’s minimum and maximum levels, to ensure
V IN
that all display readings are valid as long as the LOW BAT annunciator
remains off.
12
(–) IN LO
7
REF IN
6. Gain Adjust: There is a gain-adjust potentiometer on the back of each
1
+5V SUP
6
DP1
3
5V RET
meter. It has approximately ±50 counts (±2.5%) range of adjustment.
Since these devices essentially have no zero/offset errors, a gain
adjustment is effectively an overall accuracy adjustment. Though they
may be performed at any point (except zero), accuracy adjustments
are most effective when performed with higher level input signals. The
circuit shown in Figure 9 provides ±10% range of adjustment.
120 VAC
AC to DC Converter
Figure 2. Single-Ended Input Con?guration
(5V-Powered Models)
7. Soldering Methods: All models in the DMS-20LCD Series easily
withstand most common wave soldering operations. We recom-
mend, however, that you evaluate the effects your particular soldering
techniques may have on the meter’s plastic case and high-precision
electrical performance. We recommend the use of no-clean solders.
www.murata-ps.com/dpm
05 Apr 2011
email: sales@murata-ps.com
MPM_DMS20LCD.B08 Page 3 of 6
相关PDF资料
PDF描述
2N7000_D26Z MOSFET N-CH 60V 200MA TO-92
KIT-RMCF1206FT-06 KIT RES 1% 1206 100K-976K OHM
S1008KIT INDUCTOR KIT SHIELD S1008 180 PC
1008KIT INDUCTOR KIT 1008 SERIES 270 PC
KIT-RMCF0805FT-02 KIT RES 1% 20 EA 0805 10-97.6OHM
相关代理商/技术参数
参数描述
DMS-20LCD-0-DCM 功能描述:数字面板表 +6.50 to 1800Vdc RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20LCD-0-DCM-C 功能描述:数字面板表 +6.50 to 1800Vdc RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS20LCD1 制造商:未知厂家 制造商全称:未知厂家 功能描述:3 1/2 Digit, LCD Display Low-Cost, Subminiature Digital Panel Voltmeters
DMS-20LCD-1 制造商:未知厂家 制造商全称:未知厂家 功能描述:3 1/2 Digit, LCD Display Low-Cost, Subminiature Digital Panel Voltmeters
DMS20LCD15 制造商:未知厂家 制造商全称:未知厂家 功能描述:3 1/2 Digit, LCD Display Low-Cost, Subminiature Digital Panel Voltmeters