- 您现在的位置：买卖IC网 > Datasheet目录409 > DNT2400DK (RFM)DEVELOPMENT KIT FOR DNT2400 MOD Datasheet资料下载
参数资料
| 型号： | DNT2400DK |
| 厂商： | RFM |
| 文件页数： | 5/7页 |
| 文件大小： | 0K |
| 描述： | DEVELOPMENT KIT FOR DNT2400 MOD |
| 产品培训模块： | Frequency Hopping Spread Spectrum Portfolio Overview |
| 标准包装： | 1 |
| 类型： | 收发器 |
| 频率： | 2.4GHz |
| 适用于相关产品： | DNT2400 |
| 已供物品： | 2 个板，2 个模块，2 根天线，线缆，CD，电源 |
| 其它名称： | 583-1150 |
Pin
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Name
/HOST_RTS
RADIO_TXD
RADIO_RXD
/HOST_CTS
VMOD
RSVD
RSVD
RSVD
RSVD
/RESET
RSVD
GND
RFIO
GND
I/O
I
O
I
O
O
-
-
-
-
I
-
-
I/O
-
Description
UART flow control input. The host sets this line low to allow data to flow from the DNT2400 on the
RADIO_TXD pin. When the host sets this line high, the DNT2400 will stop sending data to the host.
UART transmitter output. The DNT2400 sends serial data to the host on this pin.
UART receiver input. The DNT2400 receives serial data from the host on this pin.
UART flow control output. The DNT2400 sets this line low to indicate it is ready to accept data from the host
on the RADIO_RXD input. When the DNT2400 sets this line high, the host must stop sending data.
Module’s +3.3 V regulated supply. Connect to pad 3 to support 3.3 V full scale and/or ratiometric ADC read-
ings, etc. Current drain on this output should be no greater than 5 mA.
Reserved pin. Leave unconnected.
Reserved pin. Leave unconnected.
Reserved pin. Leave unconnected.
Reserved pin. Leave unconnected.
Active low module hardware reset.
Reserved pin. Leave unconnected.
RF ground for the DNT2400C only. Connect to the host circuit board ground plane.
Alternate RF port for the DNT2400C only. The antenna can be connected to this port with a 50 ohm stripline
or coaxial cable. Leave unconnected when using the U.FL connector.
RF ground for the DNT2400C only. Connect to the host circuit board ground plane.
D N T 2 4 0 0 C O u tlin e a n d M o u n tin g D im e n s io n s
2 .0 1 0
0 .0 4 0
0 .0 4 0
0 .1 0 0
1
1 .2 6 0
0 .5 9 5
4 0
0 .1 8 0
D im e n s io n s in in c h e s
Figure 2
DNT2400C RFIO Stripline
The DNT2400C has a U.FL coaxial connector mounted near pad 42 for antenna connection (see Antenna Con-
nector discussion below). It is also possible to connect an antenna using a stripline from pad 42. It is important
www.RFM.com E-mail: info@rfm.com
?2009 by RF Monolithics, Inc.
Page 5 of 7
DNT2400 - 08/12/09
相关PDF资料 |
PDF描述 |
|---|---|
| DNT24DK | RF EVAL FOR DNT24P |
| DNT900DK | DEVELOPMENT KIT FOR DNT900 MOD |
| DNW1-DW10/12.5MM/BLA | LAMP T-1.25 NEO WEDGE 14V 100MA |
| DNW1-DW48/GRA | LAMP T-1.25 NEO WEDGE 14V |
| DNW1-EW87/GRA | LAMP T-1.25 NEO WEDGE 14V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DNT2400P | 功能描述:射频模块 Pin Ver 1mW/1000mW w/U.Fl Ant Connector RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| DNT24ADK | 功能描述:射频开发工具 2.4GHz Dev Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| DNT24C | 功能描述:射频模块 2.4 GHz 10 and 63mW 128 Bit AES RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| DNT24CA | 功能描述:射频模块 2.4 GHz 10 and 63mW 128 Bit AES RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| DNT24DK | 功能描述:射频开发工具 2.4 GHz 10 and 63mW Dev. Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。