- 您现在的位置：买卖IC网 > PDF目录21885 > DPM500 (Martel Electronics)LCD DPM 7.5-15V/200MV 3.5 DIGIT PDF资料下载
参数资料
| 型号： | DPM500 |
| 厂商： | Martel Electronics |
| 文件页数： | 2/2页 |
| 文件大小： | 0K |
| 描述： | LCD DPM 7.5-15V/200MV 3.5 DIGIT |
| 标准包装： | 1 |
| 系列： | Legacy |
| 类型： | 伏特表 |
| 测量范围： | 200mV |
| 显示器样式： | 黑色字符，灰色背景 |
| 显示器类型： | LCD |
| 显示器正面尺寸： | 2.36" L x 1.18" W（60.0 x 30.0mm） |
| 显示器位数： | 3.5 |
| 显示器位数 - 高度： | 0.492"（12.50mm） |
| 背光： | 无 |
| 安装类型： | 面板安装 |
| 端子： | PC 引脚 |
| 电源电压： | 7.5 ~ 14V |
| 其它名称： | 227-1009 |
Martel Electronics, Corp. P.O. Box 770 Londonderry, NH 03053
Toll Free: (800) 821-0023 Phone: (603) 434-1433 Fax: (603) 434-1653
PIN FUNCTIONS
1, 40. V+ Positive power supply.
2 -7, 12-14, 17, 38, 39 See SPECIAL NOTE: ANNUNCIATORS.
15. - Input for the polarity annunciator. Internally linked to POL (pin 20). If this is to be externally controlled, cut link 11.
16, 18, 19, 22 XB3, E3, AB, XG3. Outputs for use in auto-ranging applications.
20. POL Drive for "-" annunciator. Internally connected by link 11.
21. BP LCD backplane drive waveform.
23. DP3 1.999
24. DP2 19.99 See SPECIAL NOTE: ANNUNCIATORS.
25. DP1 199.9
26. V- Negative power supply. Note that if the DPM 500S-BL is being used, the voltage between V+ and V- must not exceed 6.5V.
27. XDP Connect to required annunciators/DPs (see note).
28. -5V Output from negative rail generator circuit. This output is an inversion of V+ (DPM 500S BL ONLY).
29. BG Input for bandgap reference. (1.22V nom).
30. IN LO Negative measuring input. Analogue inputs must be no closer than 1V to either the positive or negative supply. The negative
31. IN HI Positive measuring input. supply of the DPM 500S-BL is generated internally and mirrors the positive supply voltage.
32. COM The ground for the analogue section of the A/D converter, held actively at 2.8V (nom) below V+. COM must not be allowed to sink
excessive current (> 100 μ A) by connecting it directly to a higher voltage.
33. REF- Negative output from internal reference.
34. REF+ Positive output from internal reference.
35. REF LO Negative input for reference voltage.
36. REF HI Positive input for reference voltage.
37. TEST Connecting this pin to V+ turns on the segments as illustrated. It should not be operated for more than a few seconds as the DC
voltage applied to the LCD may "burn" the display. This pin is nominally at 5V below V+ and is the ground for the digital section
of the meter, it can be used as a negative supply to power external logic up to a maximum of 1mA.
40. V+/CLK Normally tied to V+ via Link 12 but can be used to over ride the internal oscillator and control the sample rate by cutting Link 12 and
making Link 13.
LED BACKLIT VERSIONS: Apply 5V DC to the backlight tab on the side of the meter. Typical current is 30mA. For higher voltages, fit a resistor in series.
E.g. For 9V use 150R. Maximum current = 60mA.
SPECIAL NOTE: ANNUNCIATORS: The DPM annunciators (DPs, °C, etc.) can be displayed by connecting them to XDP. However as these
annunciators are normally ‘floating’, under certain conditions they may appear when not wanted. To suppress unwanted annunciators, link them to
the backplane (BP). If the annunciators are being switched, connect them via a 1M resistor to the BP (pin 21). The annunciators will then operate
normally when connected to XDP. Ensure that an annunciator is not connected directly to the XDP and BP at the same time.
V+
+ 31 IN HI
+
IN HI
±200mV
IN LO
30
±200mV
30
- IN LO
VARIOUSOPERATINGMODES
ON-BOARD LINKS: In order to quickly and easily change operating modes for
different applications, the meter has several "on-board links". They are designed
to be easily opened(cut) or shorted (soldered).
Do not connect more than one meter to the same power supply if the meters cannot
use the same signal ground. Taking any input beyond the power supply rails will
damage the meter.
1 1
V+ V+
31
-
0V
V+
14V max
7V min
Normally
SHORTED
Cut to
OPEN
±200mV
+
-
31
30
1
V+
IN HI
IN LO
Normally
OPEN
Solder to
SHORT
V+
V-
0V
V-
26
V-
Links 1, 2, 3 & 4 SHORTED.
Measuring a floating voltage
source of 200mV full scale.
1V min V-
26
Links 1, 3 & 4 SHORTED.
Split supply operation (DPM 500).
V-
26
Links 1, 3 & 4 SHORTED.
Measuring a single ended input
referenced to supply (DPM 500S-BL).
31 IN HI
R= 0.2
V-
V-
+
+
REF HI
31
IN LO
32
V+
1
V+
R
30
IN LO
I FSR
26
Links 1, 2, 3, 4 SHORTED.
V 1
V 2
1
31 V+
IN HI
- 30 IN LO
36
- 35 REF LO
V-
26
V+
V-
I IN
6R2
I OUT
V+
1
V+
IN HI
220K
30
5K
COM
V-
26
V-
Links 1, 3 & 4 SHORTED.
Measuring current
(supply MUST be isolated).
Measuring the ratio of two voltages.
Reading = 1000 V 1 /V 2
50mV< V 2 <200mV
V 1 <2V 2 .
Measuring 4-20mA to read 0-999
(supply must be isolated).
Specifications liable to change without prior warning
DPM 500
Issue 4
July/1999
M.C.
Applies to DPM 500/7
相关PDF资料 |
PDF描述 |
|---|---|
| DPM2000 | METER DPM LCD3.5DIGIT 200MV IN |
| MX3AWT-A1-0000-000AE5 | LED NEUTRAL WHITE 4000K 2PLCC |
| MLEAWT-A1-0000-0002F5 | LED XLAMP NEUTRAL WHIT 4250K SMD |
| MLEAWT-A1-0000-0002E6 | LED XLAMP ML-E WHITE SMD |
| MLEAWT-A1-0000-0002E5 | LED XLAMP NEUTRAL WHIT 4000K SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DPM500-2 | 功能描述:METER DPM LCD 3.5DIGIT 200MV IN RoHS:否 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:- 标准包装:12 系列:* 其它名称:Q7072030 |
| DPM500-20 | 功能描述:METER DPM LCD 3.5DIGIT 20V IN RoHS:否 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:Legacy 标准包装:12 系列:* 其它名称:Q7072030 |
| DPM500-BL | 制造商:Lascar Electronics 功能描述:DIGITAL PANEL METER |
| DPM500L-20 | 功能描述:METER DPM LCD 3.5DIGIT 20V BKLT RoHS:否 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:- 标准包装:12 系列:* 其它名称:Q7072030 |
| DPM500S | 功能描述:LCD DPM 3.6-6.5V/200MV 3.5 DIGIT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:- 标准包装:12 系列:* 其它名称:Q7072030 |
发布紧急采购，3分钟左右您将得到回复。