- 您现在的位置：买卖IC网 > PDF目录9252 > DS1021S-50/T&R (Maxim Integrated Products)IC DELAY LINE 256TAP 16-SOIC PDF资料下载
参数资料
| 型号： | DS1021S-50/T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/9页 |
| 文件大小： | 0K |
| 描述： | IC DELAY LINE 256TAP 16-SOIC |
| 标准包装： | 1,000 |
| 标片/步级数： | 256 |
| 功能： | 可编程 |
| 延迟到第一抽头： | 10ns |
| 接头增量： | 0.5ns |
| 可用的总延迟： | 137.5ns |
| 独立延迟数： | 1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
DS1021
2 of 9
PARALLEL MODE (S = 1)
In the PARALLEL programming mode, the output of the DS1021 will reproduce the logic state of the
input after a delay determined by the state of the 8 program input pins P0 - P7. The parallel inputs can be
programmed using DC levels or computer-generated data. For infrequent modification of the delay value,
jumpers may be used to connect the input pins to VCC and ground. For applications requiring frequent
timing adjustment, DIP switches should be used. The enable pin (E) must be at a logic 1 in hardwired
implementations.
Maximum flexibility is obtained when the 8 parallel programming bits are set using computer-generated
data. When the data setup (tDSE) and data hold (tDHE) requirements are observed, the enable pin can be
used to latch data supplied on an 8-bit bus. Enable must be held at a logic 1 if it is not used to latch the
data. After each change in delay value, a settling time (tEDV or tPDV) is required before input logic levels
are accurately delayed.
Since the DS1021 is a CMOS design, unused input pins (D and C) must be connected to well-defined
logic levels; they must not be allowed to float.
SERIAL MODE (S = 0)
In the SERIAL programming mode, the output of the DS1021 will reproduce the logic state of the input
after a delay time determined by an 8-bit value clocked into serial port D. While observing data setup
(tDSC) and data hold (tDHC) requirements, timing data is loaded in MSB-to-LSB order by the rising edge of
the serial clock (C). The enable pin (E) must be at a logic 1 to load or read the internal 8-bit input register,
during which time the delay is determined by the last value activated. Data transfer ends and the new
delay value is activated when enable (E) returns to a logic 0. After each change, a settling time (tEDV) is
required before the delay is accurate.
As timing values are shifted into the serial data input (D), the previous contents of the 8-bit input register
are shifted out of the serial output pin (Q) in MSB-to-LSB order. By connecting the serial output of one
DS1021 to the serial input of a second DS1021, multiple devices can be daisy-chained (cascaded) for
programming purposes (Figure 3). The total number of serial bits must be eight times the number of units
daisy-chained and each group of 8 bits must be sent in MSB-to-LSB order.
Applications can read the setting of the DS1021 delay line by connecting the serial output pin (Q) to the
serial input (D) through a resistor with a value of 1K to 10K ohms (Figure 2). Since the read process is
destructive, the resistor restores the value read and provides isolation when writing to the device. The
resistor must connect the serial output (Q) of the last device to the serial input (D) of the first device of a
daisy-chain (Figure 3). For serial readout with automatic restoration through a resistor, the device used to
write serial data must go to a high impedance state.
To initiate a serial read, enable (E) is taken to a logic 1 while serial clock (C) is at a logic 0. After a
waiting time (tEQV), bit 7 (MSB) appears on the serial output (Q). On the first rising (0 → 1) transition of
the serial clock (C), bit 7 (MSB) is rewritten and bit 6 appears on the output after a time tCQV. To restore
the input register to its original state, this clocking process must be repeated eight times. In the case of a
daisy-chain, the process must be repeated eight times per package. If the value read is restored before
enable (E) is returned to logic 0, no settling time (tEDV) is required and the programmed delay remains
unchanged.
Since the DS1021 is a CMOS design, unused input pins (P1 - P7) must be connected to well-defined logic
levels; they must not be allowed to float. Serial output Q/P0 should be allowed to float if unused.
相关PDF资料 |
PDF描述 |
|---|---|
| M83723/75A2232N | CONN PLUG 32POS STRAIGHT W/SCKT |
| DS1005M-200 | IC DELAY LINE 5TAP 200NS 8-DIP |
| VI-JWK-MZ-S | CONVERTER MOD DC/DC 40V 25W |
| M83723/77W18148 | CONN PLUG 14POS STRAIGHT W/SCKT |
| DS1005M-60 | IC DELAY LINE 5TAP 60NS 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1023 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:8-Bit Programmable Timing Element |
| DS1023-025 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:8-Bit Programmable Timing Element |
| DS1023-050 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:8-Bit Programmable Timing Element |
| DS1023-100 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS1023-200 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:8-Bit Programmable Timing Element |
发布紧急采购，3分钟左右您将得到回复。