参数资料
型号: DS1050Z-005/C05+T
厂商: Maxim Integrated Products
文件页数: 17/17页
文件大小: 0K
描述: IC PWM 5BIT 5KHZ 2WIRE 8-SOIC
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
类型: 脉宽调制器(PWM)
PLL:
电路数: 1
比率 - 输入:输出: 2:1
差分 - 输入:输出: 无/无
频率 - 最大: 5kHz
电源电压: 2.7 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOIC(窄型)
包装: 带卷 (TR)
其它名称: 90-1050T+C05
DS1050
9 of 17
NOTES:
1.
All voltages are referenced to ground.
2.
ICC specified with outputs open.
3.
I/O pins of fast mode devices must not obstruct the SDA and SCL lines if VCC is switched off.
4.
Address Inputs, A0, A1, and A2, should be tied to either VCC or GND depending on the desired
address selections.
5.
ISTBY specified for VCC between 3.0V and 5.0V, control port logic pins are driven to the appropriate
logic levels.
6.
A fast mode device can be used in a standard mode system, but the requirement
tSU:DAT > 250ns must then be met. This will automatically be the case if the device does not stretch
the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal,
it must output the next data bit to the SDA line tRMAX + tSU:DAT = 1000 + 250=1250ns before the SCL
line is released.
7.
After this period, the first clock pulse is generated.
8.
The maximum tSU:DAT has only to be met if the device does not stretch the LOW period (tLOW) of the
SCL signal.
9.
A device must internally provide a hold time of at least 300ns for the SDA signal (referred to the
VIH MIN of the SCL signal) in order to bridge the undefined region of the falling edge of SCL.
10. CB – total capacitance of one bus line in picofarads, timing referenced to (0.9)(VCC) and (0.1)(VCC).
11. A PWM output duty cycle change will occur with 2 periods of the output frequency when a change is
initiated.
12. The absolute frequency output of the PWM can be expected to fall within a
±20% range from the
nominal specified value of the device.
13. The DS1050 is a 5-bit PWM. The output duty cycles of the device range from 0% to 100% in step
sizes of 3.125%. The “Set PWM Duty Cycle 100%” allows the PWM output to be set to full-on.
14. Absolute Linearity is used to compare measured duty cycle against expected duty cycle as
determined by the DAC setting. The DS1050 is specified to provide an absolute linearity of
±0.5
LSB.
15. Relative Linearity is used to determine the change in duty cycle between adjacent or successive duty
cycle settings. The DS1050 is specified to provide a relative linearity specification of
±0.25 LSB.
相关PDF资料
PDF描述
DS1050Z-001+T&R IC PWM 5BIT 1KHZ 2-WIRE 8SOIC
MS3456L12S-3P CONN PLUG 2POS STRAIGHT W/PINS
D38999/20KE6SA CONN RCPT 6POS WALL MNT W/SCKT
M83723/76W1005N CONN PLUG 5POS STRAIGHT W/PINS
M83723/76R1005N CONN PLUG 5POS STRAIGHT W/PINS
相关代理商/技术参数
参数描述
DS1050Z-010 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
DS1050Z-010/T&R 制造商:Maxim Integrated Products 功能描述:PROGRAM PWM 8P SOIC 10KHZ 2-W T&R - Tape and Reel
DS1050Z-010/T&R 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
DS1050Z-010+ 功能描述:电压模式 PWM 控制器 5 Bit 150-mil 2-Wire 10kHz PWM RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
DS1050Z-010+T&R 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:PULSE WIDTH MODULATOR 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC PWM 5BIT 10KHZ 2-WIRE 8SOIC 制造商:Maxim Integrated Products 功能描述:Clock Generators & Support Products 5 Bit 150-mil 2-Wire 10kHz PWM