- 您现在的位置：买卖IC网 > PDF目录8917 > DS1086LU-C02+ (Maxim Integrated Products)IC ECONOSILL 3.3V SS 8-USOP PDF资料下载
参数资料
| 型号： | DS1086LU-C02+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/17页 |
| 文件大小： | 0K |
| 描述： | IC ECONOSILL 3.3V SS 8-USOP |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 系列： | EconOscillator™ |
| 类型： | 扩展频谱时钟发生器 |
| PLL： | 无 |
| 输入： | 时钟 |
| 输出： | 时钟 |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:1 |
| 差分 - 输入:输出： | 无/无 |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 管件 |
3.3V Spread-Spectrum EconOscillator
Maxim Integrated
15
DS1086L
data bytes transferred between START and STOP con-
ditions is not limited, and is determined by the master
device. The information is transferred byte-wise and
each receiver acknowledges with a ninth bit.
Within the bus specifications a standard mode (100kHz
clock rate) and a fast mode (400kHz clock rate) are
defined. The DS1086L works in both modes.
Acknowledge: Each receiving device, when
addressed, is obliged to generate an acknowledge
after the byte has been received. The master device
must generate an extra clock pulse that is associated
with this acknowledge bit.
A device that acknowledges must pull down the SDA
line during the acknowledge clock pulse in such a way
that the SDA line is stable LOW during the HIGH period
of the acknowledge-related clock pulse. Of course,
setup and hold times must be taken into account.
When the DS1086L EEPROM is being written to, it is
not able to perform additional responses. In this case,
the slave DS1086L sends a not acknowledge to any
data transfer request made by the master. It resumes
normal operation when the EEPROM operation is com-
plete.
A master must signal an end of data to the slave by not
generating an acknowledge bit on the last byte that has
been clocked out of the slave. In this case, the slave
must leave the data line HIGH to enable the master to
generate the STOP condition.
Figures 4, 5, 6, and 7 detail how data transfer is
accomplished on the 2-wire bus. Depending upon the
state of the R/W bit, two types of data transfer are pos-
sible:
1)
Data transfer from a master transmitter to a slave
receiver. The first byte transmitted by the master
is the slave address. Next follows a number of
data bytes. The slave returns an acknowledge bit
after each received byte.
2)
Data transfer from a slave transmitter to a master
receiver. The first byte (the slave address) is
transmitted by the master. The slave then returns
an acknowledge bit. Next follows a number of
data bytes transmitted by the slave to the master.
The master returns an acknowledge bit after all
received bytes other than the last byte. At the end
of the last received byte, a not acknowledge is
returned.
The master device generates all the serial clock pulses
and the START and STOP conditions. A transfer is
ended with a STOP condition or with a repeated START
condition. Since a repeated START condition is also the
beginning of the next serial transfer, the bus is not
released.
The DS1086L can operate in the following two modes:
Slave receiver mode: Serial data and clock are
received through SDA and SCL. After each byte is
received, an acknowledge bit is transmitted. START
and STOP conditions are recognized as the beginning
and end of a serial transfer. Address recognition is per-
formed by hardware after reception of the slave
address and direction bit.
Slave transmitter mode: The first byte is received and
handled as in the slave receiver mode. However, in this
mode, the direction bit indicates that the transfer direc-
tion is reversed. Serial data is transmitted on SDA by
the DS1086L while the serial clock is input on SCL.
START and STOP conditions are recognized as the
beginning and end of a serial transfer.
Slave Address
Figure 5 shows the first byte sent to the device. It
includes the device identifier, device address, and the
R/W bit. The device address is determined by the
ADDR register.
Registers/Commands
See Table 1 for the complete list of registers/com-
mands and Figure 7 for an example of using them.
__________Applications Information
Power-Supply Decoupling
To achieve the best results when using the DS1086L,
decouple the power supply with 0.01μF and 0.1μF
high-quality, ceramic, surface-mount capacitors.
Surface-mount components minimize lead inductance,
which improves performance, and ceramic capacitors
tend to have adequate high-frequency response for
decoupling applications. These capacitors should be
placed as close to pins 3 and 4 as possible.
Stand-Alone Mode
SCL and SDA cannot be left unconnected when they
are not used. If the DS1086L never needs to be pro-
grammed in-circuit, including during production test-
ing, SDA and SCL can be tied high. The SPRD pin
must be tied either high or low.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1086LU-527+ | IC ECONOSCILLATOR SS 3.3V 8UMAX |
| VI-B1P-MV-F4 | CONVERTER MOD DC/DC 13.8V 150W |
| DS1086LU-440+ | IC ECONOSCILLATOR 3.3V 8USOP |
| VI-B1P-MV-F3 | CONVERTER MOD DC/DC 13.8V 150W |
| VI-B1P-MV-F2 | CONVERTER MOD DC/DC 13.8V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1086LU-C02+ | 功能描述:可编程振荡器 3.3V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1086LU-C02+T | 功能描述:可编程振荡器 3.3V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1086U | 功能描述:可编程振荡器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1086U+ | 功能描述:可编程振荡器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1086U+T | 功能描述:可编程振荡器 5V SPRD OUTPUT OSC RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
发布紧急采购，3分钟左右您将得到回复。