- 您现在的位置：买卖IC网 > PDF目录8922 > DS1086Z-11D+ (Maxim Integrated Products)IC ECONOSCILLATOR SS 8-SOIC PDF资料下载
参数资料
| 型号： | DS1086Z-11D+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/15页 |
| 文件大小： | 0K |
| 描述： | IC ECONOSCILLATOR SS 8-SOIC |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 系列： | EconOscillator™ |
| 类型： | 时钟发生器 |
| PLL： | 无 |
| 输入： | 时钟 |
| 输出： | 时钟 |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:1 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 133MHz |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
DS1086
Spread-Spectrum EconOscillator
10
______________________________________________________________________________________
ADDR Register
The A0, A1, A2 bits determine the 2-wire slave address.
The WC bit determines if the EEPROM is to be written
to after register contents have been changed. If
WC = 0 (default), EEPROM is written automatically after
a WRITE EE command. If WC = 1, the EEPROM is only
written when the WRITE EE command is issued. In
applications where the register contents are frequently
written, the WC bit should be set to 1. Otherwise, it is
necessary to wait for an EEPROM write cycle to com-
plete between writing to the registers. This also pre-
vents wearing out the EEPROM. Regardless of the
value of the WC bit, the value of the ADDR register is
always written immediately to EEPROM. When the
WRITE EE command has been received, the contents
of the registers are written into the EEPROM, thus lock-
ing in the register settings.
RANGE Register
This read-only register contains a copy of the factory-
set offset (OS). This value can be read to determine the
default value of the OFFSET register when program-
ming a new master oscillator frequency.
WRITE EE Command
This command is used to write data from RAM to
EEPROM when the WC bit in ADDR register is 1. See
the
ADDR Register section for more details.
Example Frequency Calculations
Example #1:
Calculate the register values needed to
generate a desired output frequency of 11.0592MHz.
Since the desired frequency is not within the valid mas-
ter oscillator range of 66MHz to 133MHz, the prescaler
must be used. Valid prescaler values are 2x where x
equals 0 to 8 (and x is the value that is programmed
into the P3 to P0 bits of the PRESCALER register).
Equation 1 shows the relationship between the desired
frequency, the master oscillator frequency, and the
prescaler.
By trial and error, x is incremented from 0 to 8 in
Equation 2, finding values of x that yield master oscilla-
tor frequencies within the range of 66MHz to 133MHz.
Equation 2 shows that a prescaler of 8 (x = 3) and a
master oscillator frequency of 88.4736MHz generates
our desired frequency. In terms of the device register, x
= 3 is programmed in the lower four bits of the
PRESCALER register. Writing 03h to the PRESCALER
register sets the PRESCALER to 8 (and 4% peak
dither). Be aware that the J0 bit also resides in the
PRESCALER register.
fMASTER OSCILLATOR = fDESIRED x prescaler = fDESIRED x 2X
fMASTER OSCILLATOR = 11.0592MHz x 23 = 88.4736MHz
Once the target master oscillator frequency has been
calculated, the value of offset can be determined.
Using Table 2, 88.4736MHz falls within both OS - 1 and
OS - 2. However, choosing OS - 1 would be a poor
choice since 88.4736MHz is so close to OS - 1’s mini-
mum frequency. On the other hand, OS - 2 is ideal
since 88.4736MHz is very close to the center of
OS - 2’s frequency span. Before the OFFSET register
can be programmed, the default value of offset (OS)
f
prescaler
f
DESIRED
MASTER OSCILLATOR
X
=
2
(2)
(3)
STOP
CONDITION
OR REPEATED
START
CONDITION
REPEATED IF MORE BYTES
ARE TRANSFERRED
ACK
START
CONDITION
ACK
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SLAVE ADDRESS
MSB
SCL
SDA
R/W
DIRECTION
BIT
12
6
7
8
9
12
8
9
3–7
Figure 4. 2-Wire Data Transfer Protocol
相关PDF资料 |
PDF描述 |
|---|---|
| MS3456KT16S-1P | CONN PLUG 7POS STRAIGHT W/PINS |
| DS1086LU-527+T | IC ECONOSCILLATOR SS 3.3V 8UMAX |
| DS1087LU-216 | IC ECONOSC 3.3V 16.66MHZ 8-USOP |
| MAX537AEWE+ | IC DAC 12BIT QUAD CALIB 16-SOIC |
| DS1086U+ | IC ECONOSCILLATOR SS 8-USOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1086Z-11D+ | 功能描述:可编程振荡器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1086Z-42M | 功能描述:可编程振荡器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1086Z-42M+ | 功能描述:可编程振荡器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1086Z-450+ | 功能描述:可编程振荡器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1086Z-450+T | 功能描述:可编程振荡器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
发布紧急采购，3分钟左右您将得到回复。