- 您现在的位置：买卖IC网 > PDF目录19919 > DS1216E (Maxim Integrated)IC SMARTWATCH/ROM 256K 5V 28-DIP PDF资料下载
参数资料
| 型号： | DS1216E |
| 厂商： | Maxim Integrated |
| 文件页数： | 9/15页 |
| 文件大小： | 0K |
| 描述： | IC SMARTWATCH/ROM 256K 5V 28-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 13 |
| 控制器类型： | Smartwatch ROM |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 28-DIP（0.600"，15.24mm）插口 |
| 供应商设备封装： | 28-DIP 插口 |
| 包装： | 管件 |
DS1216 SmartWatch RAM/SmartWatch ROM
3 of 15
DETAILED DESCRIPTION
The DS1216 SmartWatch RAM and SmartWatch ROM Sockets are 600-mil-wide DIP sockets with a
built-in CMOS watch function, an NV RAM controller circuit, and an embedded lithium energy source.
The sockets provide an NV RAM solution for memory sized from 2K x 8 to 512K x 8 with package sizes
from 26 pins to 32 pins. When a socket is mated with a CMOS SRAM, it provides a complete solution to
problems associated with memory volatility and uses a common energy source to maintain time and date.
The SmartWatch ROM sockets use the embedded lithium source to maintain the time and date only. A
key feature of the SmartWatch is that the watch function remains transparent to the RAM. The
SmartWatch monitors VCC for an out-of-tolerance condition. When such a condition occurs, an internal
lithium energy source is automatically switched on and write protection is unconditionally enabled to
prevent loss of watch and RAM data.
Using the SmartWatch saves PC board space since the combination of SmartWatch and the mated RAM
take up no more area than the memory alone. The SmartWatch uses the VCC, data I/O 0, CE, OE, and WE
for RAM and watch control. All other pins are passed straight through to the socket receptacle.
The SmartWatch provides timekeeping information including hundredths of seconds, seconds, minutes,
hours, days, date, months, and years. The date at the end of the month is automatically adjusted for
months with fewer than 31 days, including correction for leap years. The SmartWatch operates in either
24-hour or 12-hour format with an AM/PM indicator.
OPERATION
Communication with the SmartWatch RAM is established by pattern recognition on a serial bit stream of
64 bits that must be matched by executing 64 consecutive write cycles containing the proper data on
DQ0. On the SmartWatch ROM, communication with the clock is established using A2 and A0, and
either OE or CE. All accesses that occur prior to recognition of the 64-bit pattern are directed to memory.
After the pattern match, the next 64 reads and/or writes are directed to the clock, and the RAM is
disabled. Once the pattern is established, the next 64 read/write cycles will be directed to the RTC
registers. When power is cycled, 64 reads should be executed prior to any writes to ensure that the RTC
registers are not written. A pattern match is ignored if the RST bit is zero and the RST pin goes low
during the match sequence. A pattern match is also terminated if a read occurs during the 64-bit match
sequence.
PATTERN MATCH—RAM
Data transfer to and from the timekeeping registers is accomplished with a serial bit stream under control
of chip enable (CE), output enable (OE), and write enable (WE). Initially, a read cycle to any memory
location using the CE and OE control of the SmartWatch starts the pattern recognition sequence by
moving a pointer to the first bit of the 64-bit comparison register. Next, 64 consecutive write cycles are
executed using the CE and WE control of the SmartWatch. These 64 write cycles are used only to gain
access to the SmartWatch. Therefore, any address to the memory in the socket is acceptable. However,
the write cycles generated to gain access to the SmartWatch are also writing data to a location in the
mated RAM. The preferred way to manage this requirement is to set aside just one address location in
RAM as a SmartWatch scratch pad. When the first write cycle is executed, it is compared to bit 0 of the
64-bit comparison register. If a match is found, the pointer increments to the next location of the
相关PDF资料 |
PDF描述 |
|---|---|
| R2D12-1209/HP-R | CONV DC/DC 2W +/-9VOUT SMD |
| H472K47X7RL6UJ5R | CAP CER 4700PF 500V 10% RADIAL |
| RB-0505S | CONV DC/DC 1W SNGL 5V OUT SIP |
| T97E227K016EAB | CAP TANT 220UF 16V 10% 2917 |
| NCV8504PWADJR2G | IC REG LDO ADJ .4A 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1216F | 功能描述:IC SMART/ROM 3V 64/256/1M 32DIP RoHS:否 类别:集成电路 (IC) >> 存储器 - 控制器 系列:- 标准包装:45 系列:- 控制器类型:静态 RAM（SRAM） 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| DS1216F-3 | 功能描述:IC SMART/ROM 3V 64/256/1M 32DIP RoHS:否 类别:集成电路 (IC) >> 存储器 - 控制器 系列:- 标准包装:45 系列:- 控制器类型:静态 RAM（SRAM） 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| DS1216H | 功能描述:存储器控制器 SmartWatch RAM RoHS:否 制造商:Maxim Integrated |
| DS1216MP000 | 制造商:Thomas & Betts 功能描述:100A,PLG,2P3W,MG,216,208V |
| DS1216MR000 | 制造商:Thomas & Betts 功能描述:100A,NLT,2P3W,MG,216,208V |
发布紧急采购，3分钟左右您将得到回复。