- 您现在的位置：买卖IC网 > PDF目录381717 > DS1231 (DALLAS SEMICONDUCTOR) Power Monitor Chip(电源监控芯片) PDF资料下载
参数资料
| 型号： | DS1231 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | 电源管理 |
| 英文描述： | Power Monitor Chip(电源监控芯片) |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 封装： | 0.300 INCH, DIP-8 |
| 文件页数： | 2/9页 |
| 文件大小： | 70K |
| 代理商： | DS1231 |
DS1231/S
022698 2/9
OPERATION
The DS1231 Power Monitor detects out-of-tolerance
power supply conditions and warns a processor-based
system of impending power failure. The main elements
of the DS1231 are illustrated in Figure 1. As shown, the
DS1231 actually has two comparators, one for monitor-
ing the input (Pin 1) and one for monitoring V
CC
(Pin 8).
The V
CC
comparator outputs the signals RST (Pin 5)
and RST (Pin 6) when V
CC
falls below a preset trip level
as defined by TOL (Pin 3).
When TOL is connected to ground, the RST and RST
signals will become active as V
CC
goes below 4.75
volts. When TOL is connected to V
CC
, the RST and RST
signals become active as V
CC
goes below 4.5 volts. The
RST and RST signals are excellent control signals for a
microprocessor, as processing is stopped at the last
possible moments of valid V
CC
. On power-up, RST and
RST are kept active for a minimum of 150 ms to allow the
power supply to stabilize (see Figure 2).
The comparator monitoring the input pin produces the
NMI signal (Pin 7) when the input threshold voltage
(V
TP
) falls to a level as determined by Mode (Pin 2).
When the Mode pin is connected to V
CC
, detection oc-
curs at V
TP
-. In this mode Pin 1 is an extremely high im-
pedance input allowing for a simple resistor voltage di-
vider network to interface with high voltage signals.
When the Mode pin is connected to ground, detection
occurs at V
TP
+. In this mode Pin 1 sources 30
μ
A of cur-
rent allowing for connection to switched inputs, such as
a UL-approved opto-isolator. The flexibility of the input
pin allows for detection of power loss at the earliest point
in a power supply system, maximizing the amount of
time allotted between NMI and RST. On power-up, NMI
is released as soon as the input threshold voltage (V
TP
)
is achieved and V
CC
is within nominal limits. In both
modes of operation the input pin has hysteresis for
noise immunity (Figure 3).
APPLICATION – MODE PIN
CONNECTED TO V
CC
When the Mode pin is connected to V
CC
, pin 1 is a high
impedance input. The voltage sense point and the level
of voltage at the sense point are dependent upon the
application (Figure 4). The sense point may be devel-
oped from the AC power line by rectifying and filtering
the AC. Alternatively, a DC voltage level may be se-
lected which is closer to the AC power input than the
regulated +5-volt supply, so that ample time is provided
for warning before regulation is lost.
Proper operation of the DS1231 requires a maximum
voltage of 5 volts at the input (Pin 1), which must be
derived from the maximum voltage at the sense point.
This is accomplished with a simple voltage divider net-
work of R1 and R2. Since the IN trip point V
TP
- is 2.3
volts (using the -20 device), and the maximum allowable
voltage on pin 1 is 5 volts, the dynamic range of voltage
at the sense point is set by the ratio of 2.3/5.0=.46 min.
This ratio determines the maximum deviation between
the maximum voltage at the sense point and the actual
voltage which will generate NMI.
Having established the desired ratio, and confirming
that the ratio is greater than .46 and less than 1, the
proper values for R1 and R2 can be determined by the
equation as shown in Figure 4. A simple approach to
solving this equation is to select a value for R2 which is
high enough impedance to keep power consumption
low, and solve for R1. Figure 5 illustrates how the
DS1231 can be interfaced to the AC power line when
the mode pin is connected to V
CC
.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1231S | Power Monitor Chip(电源监控芯片) |
| DS1232LP(中文) | Low Power MicroMonitor Chip(低功耗微监控芯片) |
| DS1232LPS(中文) | Low Power MicroMonitor Chip(低功耗微监控芯片) |
| DS1232LP | Low Power MicroMonitor Chip(低功耗微监控芯片) |
| DS1232LPS | Low Power MicroMonitor Chip(低功耗微监控芯片) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1231/S | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Power Monitor Chip |
| DS123120 | 制造商:DALLAS 功能描述:* |
| DS1231-20 | 功能描述:监控电路 Power Monitor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1231-20/G | 功能描述:监控电路 Power Monitor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1231-20+ | 功能描述:监控电路 Power Monitor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。