参数资料
| 型号： | DS1236A-5+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC MICROMANAGER 5% 16-DIP |
| 标准包装： | 25 |
| 系列： | MicroManager |
| 类型： | 备用电池电路 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 25 ms |
| 电压 - 阀值： | 4.62V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-PDIP |
| 包装： | 管件 |
DS1236A
the NMI output. In addition, as long as the IN pin is less than V TP , stimulation of the ST pin will result in
additional NMI pulses. In this way, the ST pin can be used to allow the CMOS processor to determine if
the supply voltage, as monitored by the IN pin, is above or below a selected operating value. This is
illustrated in NO TAG. As discussed above, the RC pin determines the timing relationships and levels of
several signals. The following section describes the power-up and power-down timing diagrams in more
detail.
TIMING DIAGRAMS
This section provides a description of the timing diagrams shown in Figure 9, Figure 10, Figure 11, and
Figure 12. These diagrams show the relative timing and levels in both the NMOS and the CMOS mode
for power-up and down. Figure 9 illustrates the relationship for power-down in CMOS mode. As V CC
falls, the IN pin voltage drops below V TP . As a result, the processor is notified of an impending power
failure via an active NMI , which allows it to enter a sleep mode. As the power falls further, V CC crosses
V CCTP , the power monitor trip point. Since the DS1236A is in CMOS mode, no reset is generated. The
RST voltage will follow V CC down, but will fall no further than V BAT . At this time, CEO is brought high
to write protect the RAM. When the V CC reaches V BAT , a power-fail is issued via the PF and PF pins.
Figure 10 illustrates operation of the power-down sequence in NMOS mode. Once again, as power falls,
an NMI is issued. This gives the processor time to save critical data in nonvolatile SRAM. When V CC
reaches V CCTP , an active RST and RST are given. The RST voltage will follow V CC as it falls. CEO , PF,
and PF will operate in a similar manner to CMOS mode. Notice that the NMI will tri-state to prevent a
loss of battery power.
Figure 11 shows the power-up sequence for the NMOS mode. As V CC slews above V BAT , the PF and PF
pins are deactivated. An active reset occurs as well as an NMI . Although the NMI may be short due to
slew rates, reset will be maintained for the standard t RST timeout period. At a later time, if the IN pin falls
below V TP , a new NMI will occur. If the processor does not issue a ST , a watchdog reset will also occur.
The second NMI and RST are provided to illustrate these possibilities.
Figure 12 illustrates the power-up timing for CMOS mode. The principal difference is that the DS1236A
issues a reset immediately in the NMOS mode. In CMOS mode, a reset is issued when IN rises above
V TP . Depending on the processor type, the NMI may terminate the Stop mode in the processor.
WAKE CONTROL/SLEEP CONTROL
The Wake/Sleep Control input (WC/ SC ) allows the processor to disable all comparators on the DS1236A
before entering the Stop mode. This feature allows the DS1236A, processor, and static RAM to maintain
nonvolatility in the lowest power mode possible. The processor may invoke the sleep mode in battery-
operated applications to conserve battery capacity when an absence of activity is detected. The operation
of this signal is shown in Figure 13. The DS1236A may subsequently be restarted by a high-to-low
transition on the PBRST input through human interface via a keyboard, touchpad, etc. The processor will
then be restarted as the watchdog times out and drives RST and RST active. The DS1236A can also be
started up by forcing the WC/ SC pin high from an external source. Also, if the DS1236A is placed in a
sleep mode by the processor and system power is lost, the DS1236A will wake up the next time V CC rises
above V BAT . These possibilities are illustrated in Figure 14.
When the sleep mode is invoked during normal power-valid conditions, all operation on the DS1236A is
disabled, thus leaving the NMI , RST, and RST outputs disabled as well as the ST and IN inputs.
However, a loss of power during a sleep mode will result in an active RST and RST when the RC pin is
11 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| RCM28DTAD-S189 | CONN EDGECARD 56POS R/A .156 SLD |
| DS1238AS-5+ | IC MICRO MANAGER 5% 16-SOIC |
| ECM36DTBN-S273 | CONN EDGECARD 72POS R/A .156 SLD |
| EBM36DTBT-S189 | CONN EDGECARD 72POS R/A .156 SLD |
| ECM36DTBD-S273 | CONN EDGECARD 72POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1236A-5+ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1236A-5N | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1236A-5N+ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1236AN | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| DS1236AN-5 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Power Supply Supervisor |
发布紧急采购，3分钟左右您将得到回复。