- 您现在的位置：买卖IC网 > PDF目录97859 > DS1286 (DALLAS SEMICONDUCTOR) 1 TIMER(S), REAL TIME CLOCK, DIP28 PDF资料下载
参数资料
| 型号： | DS1286 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Timer or RTC |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, DIP28 |
| 封装： | PLASTIC, DIP-28 |
| 文件页数： | 6/13页 |
| 文件大小： | 234K |
| 代理商： | DS1286 |
DS1286
2 of 13
adjusted for months with less than 31 days, including correction for leap year. The Watchdog Timekeeper
operates in either 24-hour or 12-hour format with an AM/PM indicator. The watchdog timer provides
alarm windows and interval timing between 0.01 seconds and 99.99 seconds. The real time alarm
provides for preset times of up to one week.
OPERATION - READ REGISTERS
The DS1286 executes a read cycle whenever WE (Write Enable) is inactive (High) and CE (Chip
Enable) and OE (Output Enable) are active (Low). The unique address specified by the six address inputs
(A0-A5) defines which of the 64 registers is to be accessed. Valid data will be available to the eight data
output drivers within tACC (Access Time) after the last address input signal is stable, providing that CE
and OE access times are also satisfied. If OE and CE access times are not satisfied, then data access must
be measured from the latter occurring signal ( CE or OE ) and the limiting parameter is either tCO for CE
or tOE for OE rather than address access.
OPERATION - WRITE REGISTERS
The DS1286 is in the write mode whenever the WE (Write Enable) and CE (Chip Enable) signals are in
the active (Low) state after the address inputs are stable. The latter occurring falling edge of CE or WE
will determine the start of the write cycle. The write cycle is terminated by the earlier rising edge of CE
or WE . All address inputs must be kept valid throughout the write cycle. WE must return to the high state
for a minimum recovery state (tWR) before another cycle can be initiated. Data must be valid on the data
bus with sufficient Data Set Up (tDS) and Data Hold Time (tDH) with respect to the earlier rising edge of
CE
or WE . The OE control signal should be kept inactive (High) during write cycles to avoid bus
contention. However, if the output bus has been enabled ( CE and OE active), then WE will disable the
outputs in tODW from its falling edge.
DATA RETENTION
The Watchdog Timekeeper provides full functional capability when VCC is greater than 4.5 volts and
write protects the register contents at 4.25 volts typical. Data is maintained in the absence of VCC without
any additional support circuitry. The DS1286 constantly monitors VCC. Should the supply voltage decay,
the Watchdog Timekeeper will automatically write protect itself and all inputs to the registers become
“Don’t Care.” Both INTA and INTB (INTB) are open drain outputs. The two interrupts and the internal
clock continue to run regardless of the level of VCC. However, it is important to insure that the pull-up
resistors used with the interrupt pins are never pulled up to a value which is greater than VCC + 0.3V. As
VCC falls below approximately 3.0 volts, a power switching circuit turns on the lithium energy source to
maintain the clock, and timer data functionality. It is also required to insure that during this time (battery
backup mode), the voltage present at INTA and INTB (INTB) never exceeds 3.0V. At all times the
current on each should not exceed +2.1 mA or -1.0 mA. However, if the active high mode is selected for
INTB
(INTB), this pin will only go high in the presence of VCC. During power-up, when VCC rises above
approximately 3.0 volts, the power switching circuit connects external VCC and disconnects the internal
lithium energy source. Normal operation can resume after VCC exceeds 4.5 volts for a period of 150 ms.
相关PDF资料 |
PDF描述 |
|---|---|
| DS12885 | 1 TIMER(S), REAL TIME CLOCK, PDIP24 |
| DS12885T | 1 TIMER(S), REAL TIME CLOCK, PQFP32 |
| DS12887A | 1 TIMER(S), REAL TIME CLOCK, PDIP24 |
| DS12C887A | 1 TIMER(S), REAL TIME CLOCK, PDIP24 |
| DS12885S | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1286+ | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1286I | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1286I+ | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS12885 | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS12885+ | 功能描述:实时时钟 RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。